General Information & Cleaning:
Installation:
READ THIS FIRST:
Check the pack and make sure you have all of
the parts listed on the front of this booklet. If
not, contact the outlet where you bought this
product.
This product must be installed by a competent
person in accordance with the current building
and IEE wiring regulations.
As the buyer, installer and/or user of this product
it is your own responsibility to ensure that this
fitting is fit for the purpose for which you have
intended it. Eterna Lighting cannot accept any
liability for loss, damage or premature failure
resulting from inappropriate use.
If in any doubt, consult a qualified electrician.
This product is designed and constructed
according to the principles of the appropriate
British Standard and is intended for normal
domestic service. Using this fitting in any other
environments may result in a shortened working
life, for example where there is prolonged
periods of use or higher than normal ambient
temperatures.
Switch off the mains before commencing
installation and remove the appropriate circuit
fuse or lock off MCB.
The lamps supplied with this fitting are
consumable parts and therefore may be outside
of any warranty offered.
This light fitting is suitable for indoor use only.
This product is suitable is not suitable for
Bathroom use.
This product is designed for permanent
connection to fixed wiring: this must be a
suitable circuit (protected with the appropriate
MCB or fuse).
This product is suitable for installation on
surfaces with normal flammability e.g. wood,
plasterboard and masonry. It is not suitable
for use on highly flammable surfaces (e.g.
polystyrene, textiles).
If installing/mounting a light fitting to a
plastic ceiling, you must seek advice from the
ceiling manufacturer regarding the type and
specification of light fittings that may be used.
Light fittings that generate and retain heat, such
as halogen downlights or flush fittings with
incandescent lamps, may damage or discolour a
plastic ceiling.
Before making fixing hole(s), check that
there are no obstructions hidden beneath the
mounting surface such as pipes or cables.
The lamp must be positioned so that there is at
least 0.3m (300mm) between the bulb and any
illuminated surface.
When making connections ensure that the
terminals are tightened securely and that
no strands of wire protrude. Check that
the terminals are tightened onto the bared
conductors and not onto any insulation.
This fitting is double insulated; do not connect
any part to earth.
This product is not intended to be used by
children and persons with sensory, physical
and/or mental impairments that would prevent
them from using it safely.
IMPORTANT— Always switch off at the mains
before changing the lamp.
You are advised at every stage of your
installation to double-check any electrical
connections you have made. After you have
completed your installation there are electrical
tests that should be carried out, these tests are
specified in the current IEE wiring and building
regulations.
If in doubt, consult a qualified electrician.
CLEANING:
Clean this product only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
INSTALLATION:
01) Choose the location for your new light fitting
please note the conditions above.
02) The lamps are retained by a bayonet style
lampholder. Remove the lamp from the
fitting by rotating generally anticlockwise
and withdrawing.
03) The cable from the fitting can be routed
through the side of the fitting or from the
back, if you intend to route the cables from
the side then you carefully need to break out
the plastic where the cable is to exit.
04) Thread the cable back to the location you
have chosen for the mains connection. If you
are routing the cable away from the back of
the fitting and need to make a hole for the
cable to pass through.
05) Using the fitting as a template, mark the
position of the fixing holes. The fixing holes
can be found inside the fitting in the plastic
ring.
06) Secure the fittings in place using suitable
fixing screws. Ensure that the cables are not
trapped behind the fitting and are not visible
through the hole in the centre of the fitting.
(If the cable is routed across the hole in the
middle of the fitting, the lamp may not fit).
07) Connect the cable from the fittings to the
chosen connection.
08) Fit the lamp back into the lampholder
by locating the pins and rotating gently
clockwise.
09) Restore the mains supply and switch on
fitting to ensure they work satisfactorily.