READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken when
assembling, fitting or handling to prevent personal
injury or damage to the product.
This light fitting must be installed by a competent
person in accordance with the Building Regulations
making reference to the current edition of the
IEE Wiring Regulations (BS7671). The Building
Regulations may be obtained from HMSO or viewed
and downloaded from www.communities.gov.uk
following the link for Building Regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this fitting
is fit for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
The lamps (bulbs/tubes) supplied with this fitting are
consumable parts and therefore may be outside of
any warranty offered.
Switch off the mains before commencing installation
and remove the appropriate circuit fuse.
When working at heights, please use a suitable
platform.
Disconnect the fitting from the electrical supply
before flash or high voltage testing.
Suitable for indoor and outdoor use.
This product is suitable for installation on surfaces
with normal flammability e.g. wood, plasterboard,
and masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles).
Before making fixing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new fitting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
When choosing the location for your new fitting,
ensure that the fixings will be anchored in a solid
surface e.g. concrete, brick or a joist—do not fix
directly onto panelling, cladding, plasterboard etc.
If the location of your new fitting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the Building
Regulations making reference to the current edition
of the IEE Wiring Regulations (BS7671).
This product is designed for permanent connection
to fixed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp MCB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit.
We recommend that the supply incorporates a
switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product must be connected to Earth.
IMPORTANT:
Always switch off at the mains before
changing the lamp.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specified in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
INSTALLATION:
01. Choose the location for your new floodlight
giving consideration to all of the conditions listed
above.
02. Using the fixing strap as a template, mark the
position for the fixing holes on your mounting
surface.
03. Prepare your mounting surface as appropriate for
your chosen fixings (not supplied). Use a spirit
level to ensure the fitting will be level.
04. Secure the fitting in place.
05. Loosen the bolts at each end of the fixing strap
and adjust the angle of your floodlight to give the
desired spread of light.
06. Tighten the bolts to lock your floodlight in
position.
07. Make the connections to your mains supply as
described in the “Read this first” section.
08. Using a cross-headed screwdriver, undo the
screws that secure the diffuser and allow to hang
down.
09. Fit the fluorescent lamp.
10. Replace the diffuser and tighten the screws
making sure that the waterproof gasket is
correctly positioned and compressed.
11. Press the trim back onto the front of the fitting
making sure the slots used for removal are at the
bottom.
12. Restore the power and switch on.
LAMP REPLACEMENT:
01. Switch off the electricity at the mains.
02. Using a cross-headed screwdriver, undo the
screws that secure the diffuser and allow to hang
down.
03. Remove the lamp.
04. Insert new lamp.
05. Replace the diffuser and secure in position
making sure that the gasket is correctly
positioned and compressed.
06. Restore the power and switch on.
REPLACEMENT LAMP TYPE:
Fitting requires 1 x 23W ES helical CFLi 6400K
(included) or energy saving alternative.
Fitting is rated at 23W max.
