Etec E7000271 Manual Download Page 5

 

 

 

Page | 5 

 

Important safety information 

 

The manufacturer is not liable for damage caused by the failure to observe this manual or 

unauthorized modifications to this product. 

 

• The power cord must never come into contact with other cables! Use the power cord and 

all connections to the power supply. 

• Do not remove the warnings and information labels from the product.

 

• The grounding 

contact must never be tampered. 

• Make sure that no cables are around.

 

• Do not insert objects into the ventilation slots.

 

• Never connect this unit to another dimmer pack.

 

• Do not open or modify the unit.

 

• Never use the appliance during a thunderstorm. 

In the event of a thunderstorm, unplug the 

power cord immediately. 

• Do not turn the unit on and off at short intervals as this will reduce the lifetime of the unit.

 

• Do not expose the unit to shocks. Do not use excessive force when installing or using th

device. 

• Use the product only in indoor areas and avoid contact with water or other liquids.

 

• Check that the housing is tightly closed and that all screws are tightened before using the 

appliance. 

• Do not place the product near open fires or flammable

 liquids or gases. 

• Always allow at least 50cm clearance around the unit to ensure adequate ventilation.

 

• Always unplug the unit when not in use or when you want to clean it. Only hold the mains 

cable at the provided area on the plug. Never unplug the co

rd from the wall outlet. 

• Protect the product from extreme heat, moisture or dust.

 

• Make sure that the available mains voltage is not higher than indicated on the back of the 

unit. 

• Do not crush or damage the power cord. Check the unit and the power cor

d at regular 

intervals for possible damage. 

• If the connection cable is clearly damaged, it must be replaced.

 

• If the lens is clearly damaged, it must be replaced so that the functions of the unit are not 

affected by cracks or scratches. 

• Disconnect the

 appliance immediately from the power supply if it falls or becomes severely 

damaged. 

• Have the unit checked for safety by a qualified technician before using it again.

 

• Do not turn off the unit immediately after exposure to strong temperature fluctuatio

ns (eg 

during transport). The resulting condensation could damage the unit. Do not turn the unit on 

until room temperature is reached. 

•  Turn  the  power  off  immediately  if  it  is  not  working  properly.  Pack  the  device  carefully 

(preferably in the original package) and send it to your dealer. 

•  Suitable  for  adult  use  only.  The  appliance  must  be  placed  out  of  the  reach  of  children. 

Never leave the connected device unattended.

 

•  Only  use  replacement  fuses  of  the  same  type  and  performance  as  the  fuses 

already 

contained. 

• The user is responsible for the correct positioning and correct operation of the device. The 

manufacturer is not liable for damages caused by incorrect use or incorrect installation. 

• The unit falls under protection class I. Therefore

 it must be earthed with the yellow-green 

cable. 

 

Summary of Contents for E7000271



















Reviews: