ETC Hammerhead HG12 Operator And Maintenance Manual Download

Page: 8 / 108

ii Receiving and Delivery Report

HG12 Winch

General

___

Check the alternator/fan belt for proper tension.

___

Check all shields for installation and condition.

___

Check the machine for proper lubrication.

___

Check the wheel lug nuts for tightness, 90-95 ft-lb (122-130 Nm).

___

Check the tires for proper air pressure, 75 psi (5.1 bar) maximum.

___

Check the condition of all decals.

___

Check the operation of the taillights.

___

Check that the safety towing chains are installed.

___

Check that break-away brake switch is installed and functions.

___

Check all phases of operation.

___

Complete “Dealer/Customer Information”,

page iii

___

Complete “Identification Numbers - Record”,

page iv

Summary of Contents for Hammerhead HG12













































































































Search results

Summary of Contents for Hammerhead HG12

Reviews:

Related manuals for Hammerhead HG12

Brands by name

Popular brands

ETC Hammerhead HG12, Operator And Maintenance Manual

Search results

Summary of Contents for Hammerhead HG12

Reviews:

Related manuals for Hammerhead HG12

Brands by name

Popular brands