background image

Navis 100 Installation Guide

23

Compliance

For current and complete compliance information, view the product
datasheets at

etcconnect.com/Products/Lighting-Fixtures/ArcSystem-

Navis/Documentation.aspx

.

FCC - Part 15 Class A

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions : (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.

Note:

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the
interference at his own expense.

Summary of Contents for ArcSystem Navis 100





























Reviews: