background image

13

Molift Air 

Maintenance

Cleaning and disinfection

Clean on a regular basis. Clean surfaces with 

a damp cloth using an appropriate pH-neutral 

detergent. Do not use solvents or strong liquids, 

this may damage surfaces on the lifter. For 

disinfection when needed; use isopropyl alcohol. 

Avoid abrasive cleaning products. Check 

emergency stop and emergency lowering after 

cleaning. The lift should not be exposed to run-

ning water.

Make sure not to damage or 

remove labels when cleaning.

Reconditioning

Follow cleaning and installation procedure, com-

plete periodic inspection and use checklist after 

installation to recondition the lifter.

Recycling

Refer to “Recycling instructions” for how to 

properly dispose of product. 

 

Spare Parts

A list of spare parts is available on request.

Periodic Inspection Scope

Periodic inspection is a visual examination (par-

ticularly of the hoist’s load bearing structure and 

lifting mechanism with attachments, brakes, con-

trols, safety devices and person-support devices) 

according to Periodic Inspection Report for Molift 

Air. 

Periodic Inspection shall be performed at least 

once a year or more frequently if required by local 

requirements. The inspection must be performed 

by service personnel authorized by Etac. Contact 

Etac for training and authorization or recommen-

dation of an approved service partner. 

When performing a periodic inspection, the 

inspector shall fill out the inspection report for 

Molift Air. The reports should be retained by the 

person(s) responsible for servicing the hoist. If 

the inspection reveals defects and damages, the 

owner shall be notified and a copy of the report 

should be sent to Etac.

In the event of danger to safety, 

the hoist shall immediately be 

taken out of service and marked 

clearly with “out of order” and 

shall not be used until the hoist is 

repaired

When periodic inspection is completed the 

inspector shall mark the hoist with a sticker on 

the control label showing the date when periodic 

inspection is performed. The control label can be 

found on the inside of the Side cover, and this 

will then indicate when next service should be 

performed.

CONTROL

12 Month

Mark label 

with month 

and year of 

inspection

Periodic Inspection

Summary of Contents for Molift Air 205
















Reviews: