background image

6

Molift MRS Duo / www.etac.com 

Assembly

 

Adjusting post heights

1.  Lift the inner post and pull out quick release 

bolt.

2.  Lift post to desired height and insert quick 

release bolt trough outer post.

3.  Look at height labels and ensure that both 

post are adjusted at the same height.

Don`t stand under boom when 
adjusting post height

Make sure quick release bolt is 
properly installed

Don`t lift boom any higher when 
stop sign appears on height label

 End stops

1.  Lead the end stops to the desired position and 

tighten them.

2.  Make sure the liftmotor does not hit the post.
3.  Use allen key (located in top of post) to screw 

in bolts.

Mounting charger to post

1.  Remove plugs from holes on the post.
2.  Use the small allen key (located in top of post) 

to fasten screws.

3.  Fasten the lower screw first.
4.  Place charger on screw and insert second bolt.

Check list before use

Don`t start using MRS Duo before 
completing control according to 
checklist after assembly.

Use this checklist to verify that the MRS Duo is 
properly installed and can operate correctly and 
safely before use.

 

…

Make sure both bolts in foot are properly    

 fastened.

 

…

Make sure all four bolts on boom are prop  

 

early fastened.

 

…

Make sure quick release bolts are correctly  

 installed

 

…

Make sure end stops are properly fastened

Summary of Contents for 1600013













Reviews: