background image

4

www.eta.co.at

Preface

General

1

General

1.1

Preface

Dear customer,

Safe  and  satisfactory  operation  of  the  product
depends, above all, on correct installation. In this user
manual, you can find out all the important installation
steps,  information  and  instructions  for  this  product
beforehand. Please take the time to look through it.

Warranty and guarantee

You  should  also  read  the  "Conditions  for  warranty,
guarantee,  liability"  (see  chapter 

1.3  "Warranty,

guarantee and liability"

carefully. As a rule, a profes-

sional heating technician shall satisfy these conditions.
Nevertheless,  inform  the  technician  of  our  warranty
conditions.  All  of  the  requirements  we  impose  are
intended  to  prevent  damage  that  neither  you  nor  we
wish to occur.

Training the customer

To  avoid  errors  in  operation,  please  explain  to  your
customer exactly how his new product works and how
it should be operated and maintained.

Remote control of the boiler via the internet

The remote control enables you to operate your ETA
boiler remotely via your own network (VNC Viewer) or
the  internet  <www.meinETA.at>  using  a  PC,
smartphone  or  tablet,  as  though  you  were  standing
right  in  front  of  the  ETAtouch  control  system  of  your
ETA boiler. A LAN cable is required for the connection
from  the  ETAtouch  control  system  to  the  internet
modem.

Details for the remote control can be found in the
manual  "Communication  platform  meinETA".

Details  for  the  connection  of  the  LAN  cable,  see 

4.6

"Network connection"

.

Extended warranty

We grant an extended warranty if the product is com-
missioned by an authorised partner company or by our
own customer service. In this regard, please note the
warranty conditions applicable at the time of purchase.

Service agreement 

You can ensure the best care for your heating system
by  taking  out  a  service  agreement  with  one  of  our
certified contractors or our own customer service.

1.2

General information

Copyright

All  contents  of  this  document  are  property  of  ETA
Heiztechnik  GmbH  and  are  protected  by  copyright.
Any  reproduction,  transfer  to  third  parties  or  use  for
other purposes is prohibited without written permission
from the owner.

Subject to technical changes 

We reserve the right to make technical modifications
without  notice.  Printing  and  typesetting  errors  or
changes of any kind made in the interim are not cause
for  claims.  Individual  configurations  depicted  or
described  here  are  only  available  optionally.  In  the
event of contradictions between individual documents
regarding delivery scope, the information in our current
price list applies.

Explanation of symbols

Instructions and information

Layout of safety instructions

SIGNAL WORD!

Type and source of danger

Possible effects

Measures for avoiding the danger

Types of safety instruction

CAUTION!

On non-compliance with this safety instruction, there is
a risk of material damage.

WARNING!

On non-compliance with this safety instruction, there is
a risk of physical injury.

DANGER!

On non-compliance with this safety instruction, there is
a risk of major physical injury.

Summary of Contents for 11120L

















































Reviews: