DCC Operation
The LokPilot Standard works with any DCC system..
Remove any capacitors that are wired into the track
feeders (e.g. ROCO® feeder track). This could impair
the functionality of the decoder.
The address is set to 03 with 28 speed steps.
F1 switches output AUX1
F2 switches output AUX2
F3 switches the switching mode on and off
F4 switches the acceleration an deceleration on /off
F5 switches output AUX3 (if applicable)
F6 switches output AUX4 (if applicable)
DC Operation
The LokPilot Standard are set ex factory to operate
on conventional DC layouts as well. No settings are
needed to be done.
Decoder Settings (Programming)
A list of all CV parameters ist given later. These can
be changes using any DCC command station. LokPi-
lot decoders support all NMRA programming modes
as there are the programming track modes (Direct
Mode, Register Mode, Paged Mode) and the mode
for the main („POM“, „Programming on the Main“).
With RailCom® you can read CV values on the main.
RailComPlus®
Using RailComPlus®, the decoder will be automa-
itcelly recognized by a compatible command station.
You can disable this feature by deleting Bit 7 of CV
28.
Function Outputs
Each function output can be set to a certain effect.
For each physical output one CV (CV113 - CV118,
refer table page 4) is provided to define both their
behaviour (Mode) and the brightness. Please write
the following values into the corresponding CVs to
enable the following effects:
Name
Description
Brighness
Mode
Light
Normal light
0 - 15 + 0
Blink light
Phase I
Output is blinking with
defined frequency
0 - 15 + 16
Blink light
Phase II
like above, but the light is
blinking alternating
0 - 15 + 32
Strobe
Strobe light
0 - 15 + 48
firebox
Flickering light of a fire box
or braking lights
0 - 15 + 80
Zoom
Light that fades in / out
0 - 15 + 112
Marslight Mars light
0 - 15 + 128
Gyra light
Gyra light
0 - 15 + 144
Ditch light
Ditch light phase I
0 - 15 + 208
Ditch light
Ditch light phase II
0 - 15 + 244
Flash rate for blinking lights
You can also set the flash rate for all lighting effects
globally. All effects will flash or strobe at the same
rate. The desired value should be stored in CV 112.
Function Mapping
All function outputs may be assigned to the available
function buttons. Your dcc throttle may not have all
function button. Each function button is linked to a
CV in which any number of events ma be combined.
The number you enter defines the behaviour of the
output. Some functions are directional. For F0 For-
ward, it is CV33, for F0 Reverse it is CV34 and so on.
Example: Writing the value 8 into CV36 defines that
output AUX2 will listen to Function Button F2.
The following table shows the different possible
combinations and also the ex-factory settings (hown
in bold numbers):
CV Funktion
LV LR
AUX
1
AUX
2
AUX
3
AUX
4
Shun-
ting
Acc/Dec
33 F0 Forward
1
2
4
8 16 32 64
128
34 F0 Reverse
1
2
4
8 16 32 64
128
35 F1 Forward
1 2
4
8 16 32 64
128
36 F2
1 2
4
8
16 32 64
128
37 F3
1 2
4
8 16 32
64
128
38 F4 Forward
1 2
4
8 16 32 64
128
39 F5 Forward
1 2
4
8
16
32 64
128
40 F6 Forward
1 2
4
8 16
32
64
128
41 F7 Forward
1 2
4
8 16 32 64
128
42 F8
1 2
4
8 16 32 64
128
43 F9
1 2
4
8 16 32 64
128
44 F10
1 2
4
8 16 32 64
128
45 F11
1 2
4
8 16 32 64
128
46 F12
1 2
4
8 16 32 64
128
47 F1 Reverse
1 2
4
8 16 32 64
128
129 F13
1 2
4
8 16 32 64
128
130 F14
1 2
4
8 16 32 64
128
131 F15
1 2
4
8 16 32 64
128
132 F16
1 2
4
8 16 32 64
128
133 F17
1 2
4
8 16 32 64
128
134 F18
1 2
4
8 16 32 64
128
135 F4 Reverse
1 2
4
8 16 32 64
128
136 F5 Reverse
1 2
4
8 16 32 64
128
137 F6 Reverse
1 2
4
8 16 32 64
128
138 F7 Reverse
1 2
4
8 16 32 64
128
Refering to the table, locate the intersection of
•
The row of the desired function button and
•
The column for the desired function output.
There you can find the value that you have to enter
into the appropriate CV. If one function button has
to control more outputs, simply add the numbers
and write the result into the CV (33 - 138).
Abb. 4: Wiring diagram for LokPilot Standard (wiring example)
violet
orange
red
yellow
blue
green
white
black
grey
R
housing
violet
AUX2
green
AUX1
yellow
Rear
light
white
Head
light
black
orange
grey
