manualshive.com logo in svg

ESTeem AA195PM, Technical Bulletin, Page: 4 / 8

Share
Download
ESTeem AA195PM Technical Bulletin Download Page 4

Technical Bulletin 

AA195PM Assembly

 

 

 

ESTeem 

Industrial Wireless Solutions

 

 

Specifications subject to change without notice

 

415 North Quay Street 

 Kennewick, WA  99336  

 

www.esteem.com

 

Phone (509) 735-9092 

 Fax (509) 783-5475                                                           

Revised: 01 July 2016                                  

Step 6:    Pole Mounting Bracket Attachment 
 

a)

 

On  the  bottom  of  the  radio,  line  up  one  Pole  Mounting  Bracket  Assembly  with  the  exposed 
screws.  Assembly will fit width wise across the bottom of modem. 

b)

 

Using a Philips Head Screwdriver through the access holes provided in the Heat Shield, secure the 
Pole Mounting Bracket Assembly.   

c)

 

Repeat steps “a” and “b” for the second Pole Mounting Bracket Assembly. 

 

 
 
Step 7:    Ethernet Cable Boot Assembly 
 

a)

 

Slide the Ethernet Cable Boot over an outdoor rated CAT-5e Ethernet cable (Cable Not Provided). 

b)

 

Repeat for second Ethernet Cable if necessary.   

 

Figure 6: Pole Mounting Bracket Attachment 

 

Figure 7: Ethernet Cable Boot Assembly 

Summary of Contents for AA195PM









Reviews:

No comments