background image

Testing Communication Link 
 
After you have configured at least two of the Model 195Es wireless Ethernet modems for operation, you can verify 
communication with each the following steps: 
 
Status Light – The quickest source of link status is to 
view the Status Light on the face of the 195Es.  If the 
Status light is solid on the remote 195Es, the Model 
195Es has a connection to the Timing Master Model 
195Es listed in the Peer Table.  The Timing Master will 
have the status light illuminated at all times. 
 
Status Screen/Peer Table – To view further 
information on the status of the communication link 
(signal strength and last update time) you can open the 
Status Screen from the Web Interface.  After press the 
Status tab at the top of the screen the Status: Summary will be displayed showing the status of all ports and memory in the 195Es.  
Under the Wireless Status heading click on the View Peer Table (Figure 5).  The Peer Table will list all 195Es in client mode 
connected to this modem and how it is classified.   
 
Find the opposite 195Es in the Repeater Peers list and information such as signal strength (in dBm) and time/speed of last data 
packet will be displayed. 
 
 

Status LED

Solid Red on Link

 

 

Opposite Modem’s Wireless MAC

Receive Signal Strength (dBm)

Last Packet Received

Peer Modem ID

Other Access Points

 
 

Figure 5 – Repeater Peer Table 

Summary of Contents for 195Es













Reviews: