background image

11

Reversible Super Wide Side-Swing Door

1. Place towel (A) on top of dryer to protect surface.
2. Open dryer door. Remove bottom screws from cabinet side of 

hinges (D). Loosen (do not remove) top screws from cabinet 
side of hinges.

3. Lift door until top screws in cabinet are in large part of hinge 

slot. Pull door forward off screws. Set door (handle side up) on 
top of dryer. Remove top screws from cabinet.

4. Remove screws attaching hinges to door.
5. Remove screws at top, bottom and side of door (4 screws). 

Holding door over towel on dryer, grasp sides of outer door 
and carefully lift to separate it from inner door. Do not pry 
apart with putty knife. Do not pull on door seal or plastic door 
catches.

6. Be careful to keep cardboard spacer centered between doors. 

Reattach outer door panel to inner door panel so handle is on 
the side where hinges were just removed.

7. Attach door hinges to door so large part of hinge slot is at 

bottom of hinge.

8. Remove door strike (E) from cabinet. Use a small, flat-blade 

screwdriver to carefully remove 4 hinge hole plugs (F) on left 
side of cabinet. Insert plugs in hinge holes on right side of 
cabinet.

9. Insert screws in bottom holes on left side of cabinet. Tighten 

screws halfway. Position door so large end of door hinge slot 
is over screws. Slide door up so screws are in bottom of slots. 
Tighten screws. Insert and tighten top screws in hinges.

10. Remove door strike plug (B). Insert the door strike you 

removed in Step 8 in hole and secure with screw. Insert door 
strike plug in original door strike hole and secure with screw. 

11. Close door and check that door strike aligns with door catch 

(C). If needed, slide door catch left or right within slot to adjust 
alignment.

Complete Installation

1. Check to be sure all parts are now installed. If there is an extra 

part, go back through the steps to see which step was 
skipped.

2. Check to be sure you have all of your tools.

3. Dispose of all packaging materials. 
4. Check the dryer’s final location. Be sure the vent is not 

crushed or kinked.

5. Check to be sure the dryer is level. See “Level Dryer.”
6. Plug into a grounded 3 prong outlet. Turn power on.
7. Remove the blue protective film on the console and any tape 

remaining on the dryer.

8. Read your “Dryer User Instructions.”
9. Wipe the dryer drum interior thoroughly with a damp cloth to 

remove any dust.

10. Set the dryer on a full heat cycle (not an air cycle) for 

20 minutes and start the dryer.

If the dryer will not start, check the following:

Dryer is plugged into a grounded 3 prong outlet.

Electrical supply is connected.

House fuse is intact and tight, or circuit breaker has not 
tripped.

Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the 

dryer door and feel for heat. If you do not feel heat, turn the 
dryer off and check to see whether gas supply line shutoff 
valve is open. 

If the gas supply line shutoff valve is closed, open it, then 
repeat the 5-minute test as outlined above.

If the gas supply line shutoff valve is open, contact a 
qualified technician.

A

C

B

D

F

E

Summary of Contents for EGD4100SQ













Reviews: