background image

INSTALLATION MANUAL > CONTENTS

CONTENTS

I. INSTALLATION                                                                                                                                                                                                   5

1. Equipment installation                                                                                                                                                                           7

a. Fix the slit lamp to the pedestal                                                                                                                                                                         8

b. Set the objective                                                                                                                                                                                               11

c. Position the eyepiece                                                                                                                                                                                       13

2. Electrical connection                                                                                                                                                                            14

Summary of Contents for SL550L


















Reviews: