ESMT F25L02PA Series Manual Download Page 1 | Manualshive

Page: 1 / 32

ESMT F25L02PA Series Manual Download Page 1

ESMT

F25L02PA (2F)

Operation Temperature Condition -40

°

C~85

°

C

Elite Semiconductor Memory Technology Inc.

Publication D

ate

:

Jan. 2012

Revision

:

1.0

1/32

Flash

3V Only 2 Mbit Serial Flash Memory

with Dual Output

FEATURES

Single supply voltage 2.3~3.6V

Standard, Dual SPI

Speed

- Read max frequency: 33MHz
- Fast Read max frequency: 50MHz; 86MHz; 100MHz
- Fast Read Dual max frequency: 50MHz / 86MHz
(100MHz / 172MHz equivalent Dual SPI)

Low power consumption

- Active current: 20 mA
- Standby current: 25

µ

A

- Deep Power Down current: 10

µ

A

Reliability

- 100,000 typical program/erase cycles
- 20 years Data Retention

Program

- Page programming time: 0.7 ms (typical)

Erase

- Chip erase time 0.5 sec (typical)
- Block erase time 0.15 sec (typical)
- Sector erase time 30 ms (typical)

Page Programming

- 256 byte per programmable page

SPI Serial Interface

- SPI Compatible: Mode 0 and Mode 3

End of program or erase detection

Write Protect ( WP )

Hold Pin ( HOLD )

All Pb-free products are RoHS-Compliant

ORDERING INFORMATION

Product ID

Speed

Package

Comments

F25L02PA -50PIG2F

50MHz

F25L02PA -86PIG2F

86MHz

F25L02PA -100PIG2F

100MHz

8-lead

SOIC

150 mil

Pb-free

F25L02PA -50PAIG2F

50MHz

F25L02PA -86PAIG2F

86MHz

F25L02PA -100PAIG2F

100MHz

8-lead

SOIC

200 mil

Pb-free

F25L02PA -50HIG2F

50MHz

F25L02PA -86HIG2F

86MHz

F25L02PA -100HIG2F

100MHz

8-contact

WSON

6x5 mm

Pb-free

GENERAL DESCRIPTION

The  F25L02PA  is  a  2Megabit,  3V  only  CMOS  Serial  Flash
memory  device.  The  device  supports  the  standard  Serial
Peripheral  Interface  (SPI),  and  a  Dual  SPI.  ESMT’s  memory
devices  reliably  store  memory  data  even  after  100,000
programming and erase cycles.

The  memory  array  can  be  organized  into  1,024  programmable
pages of 256 byte each. 1 to 256 byte can be programmed at a
time with the Page Program instruction.

The device features sector erase architecture. The memory array

is  divided  into  64  uniform  sectors  with  4K  byte  each;  4  uniform
blocks  with  64K  byte  each.  Sectors  can  be  erased  individually
without affecting the data in other sectors. Blocks can be erased
individually without affecting the data in other blocks. Whole chip
erase  capabilities  provide  the  flexibility  to  revise  the  data  in  the
device. The device has Sector, Block or Chip Erase but no page
erase.

The  sector  protect/unprotect  feature  disables  both  program  and
erase  operations  in  any  combination  of  the  sectors  of  the
memory.

1
2
3
...
»

Summary of Contents for F25L02PA Series

































Reviews:

No comments