3.3
1.
2.
3.
4.
5.
6.
CHARGING
Charge the
ESKUTE
ES1 before using it.
The charge cycle is complete when the battery indicator on display is full. Each charge cycle from zero
to full charge will take approximately
5~6 hrs. When the backlit display on the handlebars indicates that
battery power is low, recharge the ES1. To recharge the ES1, use the included charger.
Step 1.
Step 2.
Step 3.
Step 4.
DO NOT(under any circumstances)use the scooter while it is charging or connected to the charger.
r
o
/
d
n
a
e
fi
l
y
r
e
tt
a
b
t
c
e
ff
a
y
a
m
t
a
h
t
n
a
h
t
r
e
g
n
o
l
g
n
i
g
r
a
h
C
.
s
r
u
o
h
6
~
5
y
l
e
t
a
m
i
x
o
r
p
p
a
s
i
e
m
it
g
n
i
g
r
a
h
c
e
h
T
performance. If the charger’s light doesn’t turn on, it may not be fully connected. Check that it is securely
connected to the wall and to the scooter.
RIDING OPERATION
We sincerely hope every operator can ride the ESKUTE
e
r
o
f
e
b
n
o
it
a
m
r
o
f
n
i
g
n
i
w
o
ll
o
f
e
h
t
e
t
o
N
.
y
l
e
f
a
s
1
S
E
attempting to ride your ESKUTE ES1.
●
●
●
●
●
5.1
First, choose a suitable venue for riding. Next, unfold the scooter in accordance with the instructions. Last,
adjust the T-pipe to the suitable height according to your height.
●
●
●
●
●
●
●
Non-Pneumatic Tires
Inflation-free, maintenance-free, explosion-proof, anti-tie.
The wheel hub is fitted with the inner tube tire tightly, and the steel wire protection is more safe.
Excellent flexibility. The foamed inner tube adopts microwave closed-cell foaming to make the
performance of comfortability close to the traditional inflation tire.
Foamed inner tube adopts improved rubber and improved polymer environmental protection materi-
als, and the products are environmentally friendly and non-toxic.
Wear-resistant and anti-skidding. The shell uses a traditional rubber tire which has good perfor-
mance, and passed the market testing.
Weather resistance. It features with high temperature resistance, low temperature resistance and
aging resistance.
An ASTM F1492 approved helmet as well as other protective gear must be worn at all times.
The ES1 supports up to 265 lbs (120 kg).
Before each ride, especially if you may travel a long distance, check the front tire for proper inflation,
check all cables for damage, and test the brakes. Do not ride if any part of the scooter is damaged or
malfunctioning.
Only operate the ESKUTE ES1 where permitted. Local laws may restrict where you may ride.
In compliance with UL2272 standards, power to the ESKUTE ES1 motorized wheel may cut off during
continuous uphill travel and/or other cases which cause the motor to overheat. If the motor overheats,
this safety feature will trigger automatically. Stop riding and allow 15 minutes before using the motor
again. In general, continuous uphill travel at 14° slopes for long periods of time is not recommended.
Getting Ready
Start your scooter by pressing and holding the power button for 3~5 seconds.
Moving forward with your scooter is as easy as pressing the throttle.
Cruising is as simple as maintaining speed for at least 2 seconds.
Use the bell to alert pedestrians and other riders of your presence.
Turn the headlight on/off by quick-pressing the power button twice.
The display shows how much battery power is left.
Make sure the scooter is powered off then locate the charging port under the deck.
Insert the appropriate end into the charging port and then insert the other end into an outlet.
While the scooter is charging, the charger light will turn red.
When the scooter is fully recharged, the charger light will turn green. You may then disconnect
the scooter from the charger.
- 05 -
Switch gears between 1,2 by quick-pressing the power button once. Each gears has different speed.
Gear 1’s max. Is 9 mph, Gear 2’s is 15 mph.