Eskimo MAKO Operator'S Manual Download Page 3

3

Check for parts online at 

www.GetEskimo.com

 

or

 call 

800-345-6007

 M-F 8-5 CDT

Operator's Manual

ESKIMO

®

 

Power Ice Auger

WARNINGS AND SAFETY PRECAUTIONS

OPERATOR’S RESPONSIBILITY

Accurate, safe and effective use of this unit is the operator’s 

responsibility.

•  Read and follow all safety instructions.
•  Carefully follow all assembly instructions.
•  Maintain  the  unit  according  to  directions  and  schedule 

included in this Eskimo operator’s manual.

•  Ensure that anyone who uses the unit is familiar with and 

understands all controls and safety precautions.

SAFETY MESSAGES

Your manual contains special messages to bring attention to 

potential safety concerns, engine damage as well as helpful 

operating and servicing information. Please read all the infor-

mation carefully to avoid injury and damage to the unit.

NOTE: General information is given throughout the manual 

that may help the operator in the operation or service of the 

unit.

 

This symbol points out important safety instruc-

tions which if not followed could endanger your 

personal safety. 

BEFORE OPERATING: 

 

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT 

AVOIDED, COULD RESULT IN DEATH OR SERIOUS IN-

JURY AND/OR PROPERTY DAMAGE.

 CAUTION

CAUTION INDICATES YOU CAN BE HURT OR YOUR 

EQUIPMENT DAMAGED IF THE SAFETY INSTRUC-

TIONS THAT FOLLOW THIS SIGNAL WORD ARE NOT 

OBEYED.

 WARNING

CALIFORNIA PROPOSITION 65 WARNING

ENGINE EXHAUST FROM THIS PRODUCT CONTAINS 

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA 

TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER RE-

PRODUCTIVE HARM.

 IMPORTANT

INDICATES HELPFUL INFORMATION FOR PROPER AS-

SEMBLY, OPERATION, OR MAINTENANCE OF YOUR 

EQUIPMENT.

 WARNING

FAILURE TO COMPLY WITH ALL SAFETY AND OPERAT-

ING INSTRUCTIONS CAN RESULT IN LOSS OF ENGINE 

CONTROL, SERIOUS PERSONAL INJURY TO YOU AND/

OR BYSTANDERS, AND RISK OF EQUIPMENT AND 

PROPERTY DAMAGE. 

 WARNING

READ ENTIRE OPERATING AND MAINTENANCE 

INSTRUCTIONS FOR THIS PRODUCT AND THE 

INSTRUCTIONS FOR THE EQUIPMENT THIS ENGINE 

POWERS.  FAILURE TO FOLLOW INSTRUCTIONS COULD 

RESULT IN SERIOUS INJURY OR DEATH. OPERATE THE 

ENGINE ACCORDING TO THE SAFETY INSTRUCTIONS 

OUTLINED HERE AND INSERTED THROUGHOUT THE 

TEXT.  ANYONE WHO USES THIS UNIT MUST READ THE 

INSTRUCTIONS AND BE FAMILIAR WITH THE CONTROLS.

SAFETY DECALS:

Below are three of the warning decals attached to the auger. It is 

important to read all safety precautions and locate the warning 

labels before using this product.

     WARNING!

Failure  to  read,  understand  and 

follow  all  warnings  and  instruc-

tions  listed  could  result  in  seri-

ous injury or death. Keep all body 

extremities,  loose  clothing  and 

foreign  objects  clear  of  rotating 

auger. Be sure auger is securely 

attached  to  powerhead  during 

use. Never carry auger between 

holes  with  the  engine  running. 

This auger is not designed to be 

utilized  as  an  anchoring  device. 

Use this auger/powerhead as per 

provided instructions only.

LBLAUGER     R061909

Summary of Contents for MAKO















Reviews: