Eskimo CR132-RG57A3 Manual Download Page 8

8m

MODE

SWING

TEMP

SHORTCUT

   FAN

SPEED

   TIMER

     OFF

   RESET

   LOCK

       LED

FOLLOW ME

TIMER

  ON

      TURBO

SELF CLEAN

DIRECT

SLEEP

FRESH

Use the remote controller within a distance of 8 
meters from the appliance, pointing it towards the 
receiver. Reception is confirmed by a beep.

The remote controller can be attached to a wall or pillar
by using a remote controller holder(not supplied,
purchased separately).
Before installing the remote controller, check that the
air conditioner receives the signals properly.
Install the remote controller with two screws.
For installing or removing the remote controller, move
it up or down in the holder.

The following cases signify exhausted batteries.
Replace old batteries with new ones.
   Receiving beep is not emitted when a signal
    is transmitted.
    Indicator fades away.

Location of the remote controller.

Using the remote controller holder(optional)

Your air conditioning unit may come with two 
batteries(some units). Put the batteries in the 
remote control before use:
(1) Remove the cover in the rear part of the 
      remote controller.
(2) Remove the old batteries and insert the new 
     batteries, placing the(+) and (-) ends correctly.
(3) Install the cover back on.

NOTE: 

When the batteries are removed, the 

remote controller erases all programming.  After 
inserting new batteries, the remote controller 
must be reprogrammed.
  

Replacing batteries

CAUTIONS

The air conditioner will not operate if curtains, 
doors or other materials block the signals from 
the remote controller to the indoor unit.
Prevent any liquid from falling into the remote 
controller. Do not expose the remote controller 
to direct sunlight or heat.
If the infrared signal receiver on the indoor unit 
is exposed to direct sunlight, the air conditioner 
may not function properly. Use curtains to 
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote 
controller, either move these appliances or 
consult your local dealer.
Do not drop the remote controller. Handle with care.
Do not place heavy objects on the remote controller,
or step on it.

CAUTIONS

Do not mix old and new batteries or batteries 
of different types.
Do not leave the batteries in the remote 
controller if they are not going to be used for 
2 or 3 months.
Do not dispose batteries as unsorted 
municipal waste. Collection of such waste 
separately for special treatment is necessary.

Handling the remote controller

13

14

Summary of Contents for CR132-RG57A3

























Reviews: