ESI Enmo 2NM-C48-BLK Assembly And Operation Instructions Manual Download Page 4 | Manualshive

Page: 4 / 12

background image

Page 4

Enmo

Assembly

Step #3: attach feet

• Attach a foot to each leg with four M6x14 screws per foot.

Step #4: attach top supports

• Turn the frame upright.

• Attach the top supports to the end of the frame with two M6x12 screws per support.

4mm Allen key

M6x14

top

support

top

support

4mm Allen key

M6x12

«
...
2
3
4
5
6
...
»

Summary of Contents for Enmo 2NM-C48-BLK













Reviews:

No comments

Related manuals for Enmo 2NM-C48-BLK

Brand: Dario Pages: 7

Brand: JD Williams Pages: 9

Brand: Salamander Designs Pages: 4

Brand: Watson Desking Pages: 2

Brand: WATSON Pages: 2

Brand: Wallbeds Australia Pages: 3

Brand: GALA MEBLE Pages: 15

Findley & Myers CBD36

Brand: CABINETS TO GO Pages: 4

Brand: DaVinci Pages: 36

Brand: Article Pages: 10

Brand: EURO3PLAST SPA Pages: 4

Brand: Next Pages: 14

Brand: Nucraft Pages: 13

Brand: Original Steifensand Pages: 16

Chelsea 85992KFRS1

Brand: Garden Wood Furniture Pages: 6

Portland Headboard

Brand: Atlantic Furniture Pages: 3

Paris Storage 424586

Brand: Next Pages: 11

Brand: Furinno Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands