ESI 2TD-C48-24-BLK Assembly Instructions Manual Download Page 8

Page: 8 / 12

Page 8

Trada 2-leg

Assembly

Step #9: attach handset

• Position the handset on either side of the table (user preference).

NOTE:

With the table face-down, the left side will be the right side when the table is turned upright.

• Position the handset so that the controls are flush with the front edge of the table.

• Attach the handset using two #6x

" Phillips round head screws.

Step #10: attach control unit

• Position the control unit in front of the front crossbar, approximately centered on the worksurface from side-to-side.

• Attach the control unit using the two #6x

" Phillips round head screws.

Step #11: attach power supply

• Fit the power supply into the power supply holder.

• When the table is turned upright, the power cord end should be the end closest to the nearest AC outlet.

Step #12: make cable and cord connections

• Connect the cable from the handset to the control unit.

• Connect the motor cables from the legs to the control unit.

• Connect the cable from the power supply to the control unit.

• Connect the power cord to the power supply.

• Plug the power cord into an AC outlet. Be sure the cord will be able to reach the outlet when the table is raised to its highest position.

CAUTION:

Do not operate the table until after initializing the system. See the following step.

handset

control unit

handset cable

#6x

Phillips round head

motor cable

power supply

cable

power

supply

power supply

holder

motor cable

power cord

Summary of Contents for 2TD-C48-24-BLK













Search results

Summary of Contents for 2TD-C48-24-BLK

Reviews:

Related manuals for 2TD-C48-24-BLK

Brands by name

Popular brands

ESI 2TD-C48-24-BLK, Assembly Instructions Manual

Search results

Summary of Contents for 2TD-C48-24-BLK

Reviews:

Related manuals for 2TD-C48-24-BLK

Brands by name

Popular brands