STANDARDS CONFORMITY
An
drives
inverter fitted with this Option complies with the
following standards:
CE-marked for Low Voltage Directive.
IEC 664-1 Insulation Coordination within Low Voltage Systems.
UL 840 Insulation Coordination for electrical equipment.
EN50081-2 EMC Generic Emissions Standard, Industrial Level.
EN50082-2 EMC Generic Immunity Standard, Industrial Level.
Enclosure ingress protection, EN60529 IP00, NEMA 250.
Flammability rating according to UL 94.
User Guide
All rights reserved. No part of this User Guide may be reproduced or
transmitted in any form or by any means, electrical or mechanical
including photocopying, recording or by any information storage or
retrieval system without permission in writing from the publisher.
Copyright
©2017
The manufacturer accepts no liability for any consequences resulting
from inappropriate, negligent or incorrect installation.
The contents of this User Guide are believed to be correct at the time of
printing. In the interests of a commitment to a policy of continuous
improvement, the manufacturer reserves the right to change the
specification of the product or its performance or the contents of the User
Guide without notice.
SAFETY
This option is specifically designed to be used with the
drives
inverter and is intended for professional incorporation into complete
equipment or systems. If installed incorrectly it may present a safety
hazard. The
drives
inverter uses high voltages and currents,
carries a high level of stored electrical energy, and is used to control
mechanical plant that may cause injury. Close attention is required to
system design and electrical installation to avoid hazards in either normal
operation or in the event of equipment malfunction.
System design, installation, commissioning and maintenance must be
carried out only by personnel who have the necessary training and
experience. They must read carefully this safety information and the
instructions in this Guide and follow all information regarding transport,
storage, installation and use of the Option module, including the specified
environmental limitations.
Please read the IMPORTANT SAFETY INFORMATION below, and all
Warning and Caution boxes elsewhere.
CAUTION
Store the Option in its box until
required. It should be stored in a
clean
and
dry
environment.
Temperature range
–40
o
C to
+60
o
C.
Install
the
Option
onto
the
drives
inverter by inserting
the row of 11 pins into the terminal
connector of the inverter, ensuring
that the terminals are tightened.
If the Option is being used with
Size#1
drives
, care should
be taken to support the Option
when the terminal screws of the
Option are being tightened or
loosened.
WARNING
drives
inverters and the
Options should be installed only by
qualified electrical persons and in
accordance with local and national
regulations and codes of practice.
Electric
shock
hazard!
Disconnect and
ISOLATE
the
drives
inverter
before
attempting any work on it. High
voltages are present at the
terminals and within the drive for
up
to
10
minutes
after
disconnection of the electrical
supply.
Where the electrical supply to the
drive is through a plug and socket
connector, do not disconnect until
10 minutes have elapsed after
turning off the supply.
drives
HVAC RELAY
EDS3HVAC
OPTION MODULE
SAFETY NOTICES
WARNING
is given where there
is a hazard that could lead to
injury or death of personnel.
CAUTION
is given where there
is a hazard that could lead to
damage to equipment.
It is the responsibility of the
installer to ensure that the
equipment or system into which
the product is incorporated
complies
with
the
EMC
legislation of the country of use.
Within the European Union,
equipment
into
which
this
product is incorporated must
comply
with
89/336/EEC,
Electromagnetic Compatibility.
WARRANTY
Complete Warranty Terms and
Conditions are available upon
request from your
drives
inverter Authorized Distributor.
www.escodrives.com
WARNING
Within the European Union, all
machinery in which this product
is used must comply with the
Directive 89/392/EEC, Safety of
Machinery. In particular, the
equipment should comply with
EN60204-1.
