esatto.house
11
Operation Instructions
NOTE:
•
Should you like to keep your appliance connected to a power source continuously, please enter the
operational mode before the standby state after each power on.
•
If an unexpected power outage has occurs (eg. when the power is off or the power cord is unplugged
during normal operation), the previous state will resume when the power is restored to the appliance.
BEFORE FIRST TIME USE:
1
Remove the protective film of the filter assembly.
2
Install the filter
3
Power on for the first time, the display panel flashes for 1s, and then the screen is turned off.
The whole appliance is the standby state;
4
On/Standby: Press the On/Standby button
5
Operation: The purifier is powered on for the first time and then enters the Turbo mode.
Note: This model is equipped with a memory function and will enter the mode that was last used.
6
3
Flash for 1s
Preparation
Power on for the first time, the display
panel flashes for 1s, and then the screen
is turned off. The whole appliance is the
standby state;
2
Install the filter
5
Warm up
When the particulate matter sensor enters
the warm-up state, Air quality indicator
and is normal after 3s light will flash in
sequence.
6
Work
The purifier is powered on for the first
time and then enters the automatic mode.
4
On/standby
Press on/standby button.
INSTRUCTIONS
Test Run
Note:
• In case of continuous electricity, enter the working mode before the standby
state, after each power on.
• The appliance is connected to the power again after unexpected power outage
(when the power is off or the power cord is unplugged during normal operation),
and then restores to the working state before the power outage.
1
Remove the protective film of the
filter assembly.
6
3
Flash for 1s
Preparation
Power on for the first time, the display
panel flashes for 1s, and then the screen
is turned off. The whole appliance is the
standby state;
2
Install the filter
5
Warm up
When the particulate matter sensor enters
the warm-up state, Air quality indicator
and is normal after 3s light will flash in
sequence.
6
Work
The purifier is powered on for the first
time and then enters the automatic mode.
4
On/standby
Press on/standby button.
INSTRUCTIONS
Test Run
Note:
• In case of continuous electricity, enter the working mode before the standby
state, after each power on.
• The appliance is connected to the power again after unexpected power outage
(when the power is off or the power cord is unplugged during normal operation),
and then restores to the working state before the power outage.
1
Remove the protective film of the
filter assembly.
6
3
Flash for 1s
Preparation
Power on for the first time, the display
panel flashes for 1s, and then the screen
is turned off. The whole appliance is the
standby state;
2
Install the filter
5
Warm up
When the particulate matter sensor enters
the warm-up state, Air quality indicator
and is normal after 3s light will flash in
sequence.
6
Work
The purifier is powered on for the first
time and then enters the automatic mode.
4
On/standby
Press on/standby button.
INSTRUCTIONS
Test Run
Note:
• In case of continuous electricity, enter the working mode before the standby
state, after each power on.
• The appliance is connected to the power again after unexpected power outage
(when the power is off or the power cord is unplugged during normal operation),
and then restores to the working state before the power outage.
1
Remove the protective film of the
filter assembly.
6
3
Flash for 1s
Preparation
Power on for the first time, the display
panel flashes for 1s, and then the screen
is turned off. The whole appliance is the
standby state;
2
Install the filter
5
Warm up
When the particulate matter sensor enters
the warm-up state, Air quality indicator
and is normal after 3s light will flash in
sequence.
6
Work
The purifier is powered on for the first
time and then enters the automatic mode.
4
On/standby
Press on/standby button.
INSTRUCTIONS
Test Run
Note:
• In case of continuous electricity, enter the working mode before the standby
state, after each power on.
• The appliance is connected to the power again after unexpected power outage
(when the power is off or the power cord is unplugged during normal operation),
and then restores to the working state before the power outage.
1
Remove the protective film of the
filter assembly.
6
3
Flash for 1s
Preparation
Power on for the first time, the display
panel flashes for 1s, and then the screen
is turned off. The whole appliance is the
standby state;
2
Install the filter
5
Warm up
When the particulate matter sensor enters
the warm-up state, Air quality indicator
and is normal after 3s light will flash in
sequence.
6
Work
The purifier is powered on for the first
time and then enters the automatic mode.
4
On/standby
Press on/standby button.
INSTRUCTIONS
Test Run
Note:
• In case of continuous electricity, enter the working mode before the standby
state, after each power on.
• The appliance is connected to the power again after unexpected power outage
(when the power is off or the power cord is unplugged during normal operation),
and then restores to the working state before the power outage.
1
Remove the protective film of the
filter assembly.
1
2
3
4
5
6
Flash for 1 sec.
