ES&S DS850 Operator'S Manual Download

Page: 36 / 199

Chapter 3: DS850 User Interface

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

Hardware Menu

The Hardware menu lists the following options:











The following is an example of
the Hardware menu.

Screen Calibration

Press

Screen Calibration

to calibrate the scanner’s touch screen.

Printers

The Printers option on the Hardware menu allows you to print test pages on the report
and log printers.

Follow the steps below to print test pages on these printers:

From the Hardware menu, press

Printers

Reference:

Refer to the

ES&S DS850 System Maintenance Manual

for further information on

calibrating the scanner’s touch screen.

Summary of Contents for DS850








































































































































































































Search results

Summary of Contents for DS850

Reviews:

Related manuals for DS850

Brands by name

Popular brands

ES&S DS850, Operator'S Manual

Search results

Summary of Contents for DS850

Reviews:

Related manuals for DS850

Brands by name

Popular brands