User manual – ES-AW-8
GENERAL CONDITIONS
Moduł awaryjny należy instalować zgodnie z niniejszą instrukcją, z zachowaniem norm dotyczących bezpieczeństwa użytkowania. Wszelkie czynności instalacyjne i konserwacyjne należy wykonywać
The emergency module must be installed in accordance with these instructions, while maintaining safety standards. All installation and maintenance activities must be carried out after disconnecting the
supply voltage and the battery. Installation and maintenance may only be performed by authorized persons.
Making changes in the device’s design and using it under conditions other than those described in these instructions is prohibited.
FEATURES
Emergency module for use with LED light sources.
• The emergency module’s electronic system features the following functions:
• - automatic battery charging
• - battery protection against deep discharge
• - indicating correct functioning or damage to the module
The set includes:
• - the electronics encased in housing
• - maintenance-free Ni-MH batteries
• - mounting brackets or battery housing depending on the application
• - instruction manual
OPERATION MODE INDICATION
LED
Operation mode
On
Correct operation, charger working
Off
Emergency operation, not charging
GUARANTEE
ES-SYSTEM guarantees the correct and reliable operation of its devices (according to the general terms and conditions), provided they are used as intended and in accordance with the principles in the
instructions. The products are manufactured using the latest technologies and compliant with Polish standards and harmonized European Union standards.
WIRING DIAGRAMS
FUNCTIONING PRINCIPLES
First-time operation
Due to the construction of the Ni-MH battery and in order to ensure its proper formation, it is recommended that its first charging lasts 48 hours. During this time, emergency operation is not allowed and no
testing can be performed. After this time, the module must be switched to emergency operation (by disconnecting the voltage in the L* line). The module should operate in this mode until the batteries are
completely depleted. The power supply voltage must then be switched back on, and the batteries must be charged for at least 36 hours in order to complete the formation cycle.
USE
Testing:
The emergency module functionality must be tested regularly (in accordance with the PN-EN 50172 standard) by disconnecting the voltage in the L* control line or by using the optional P2 button connec-
ted to the T1, T2 terminals.
Supporting functions:
Emergency mode blocking is possible using the control signal from the RM unit. Once the block is activated, the module will not switch to the emergency mode during a power failure in the L* line. Once mains
power is restored to the L*line, normal operation will resume. Blocking the emergency mode from the RM control unit with a bi-stable connector maintains the emergency mode block until it is removed.
Detailed technical information and wiring diagrams can be found in the instruction manual of the RM control unit.
INSTALLATION
The components of the emergency module are intended for installation in a luminaire. The LED indicator must be visible during use and in different conditions, for example in the ceiling void – this is mandatory
due to safety requirements applicable during the use of electrical devices and installations. The cable length between the emergency module and the 1W LED may not be longer than 1 m. The emergency
module and the battery must not be placed near heat sources. The temperature of the electronics housing measured at the Tc point must not exceed the maximum value. The voltage control line L* must not
include switches or other devices which could disconnect the line. The luminaire connection system should be carried out according to one of the wiring diagrams included in this instruction manual. Before
switching on the voltage, it is necessary to make sure that all the connections have been performed correctly.
Charging the battery with any device other than the electronics system of the emergency module is not allowed.
ES-AW-8 STI technical data
Power supply voltage
230 VAC +-10% 50-60Hz
Maximum power consumption
6W
Ingress protection rating
IP20
Safety class
II
Operating temperaturę range
Ta = 0..+50*C
Weight of the electronics
0,36 kg
Wire cross-section
0,2 – 1,5 mm^2
Ordering codes
Autonomy time
ES-AW-8
1h
3h
260mA
9346110
ES-AW-8-SKTA/TC1
9346130
ES-AW-8-SKTA/TC3
450mA
9346210
ES-AW-8-SLTA/TC1
9346230
ES-AW-8-SLTA/TC3
700mA
9346310
ES-AW-8-SMTA/TC1
9346330
ES-AW-8-SMTA/TC3
1200mA
9346410
ES-AW-8-SNTA/TC1
9346430
ES-AW-8-SNTA/TC3
Faulty emergency modules and batteries must
be returned to the supplier for recycling.
The dimensions of the emergency module and the battery
RM
RM
RM
RM
L*
L
N
N
L*
L
RM
RM
-
+
-
+
INHIBIT MODE
230 V
50 Hz
INHIBIT MODE
LED
BAT
ES-AW-8 MODULE
N
L*
L
RM
RM
-
+
-
+
230 V
50 Hz
LED
BAT
ES-AW-8 MODULE
L*
L
N
N
L*
L
DA
DA
-
+
-
+
DALI / CTI
230 V
50 Hz
LED
BAT
ES-AW-8 MODULE
DA
DA
N
L*
L
DA
DA
-
+
-
+
DALI / CTI
230 V
50 Hz
LED
BAT
ES-AW-8 MODULE
DA
DA
STI
CTI/A
TI
/CTI-DALI
LED INDICATOR
LED INDICATOR
LED INDICATOR
LED INDICATOR
190
23
232
30
31
30
32
02.2016
