manualshive.com logo in svg

Ericsson ROK 101 007, Manual, Page: 19 / 21

Share
Download
Ericsson ROK 101 007 Manual Download Page 19

ROK 101 007

19

Preliminary

APPENDIX B

Development tools

Ericsson Bluetooth Development
Kit (EBDK)

The easiest way of getting started is
to use the Ericsson Bluetooth
Developers Kit. It provides all parts
necessary for developing applica-
tions for the Bluetooth module.

Available are:

•

PC plug&play

•

Demos using radio/baseband

•

Macro capability

•

C++ v5.0 Source code for use in

applications

•

HCIdriver, L2CAP, SDP and

RFCOMM for applications using

UART communication

•

Pins for electrical measurements

•

Antennas

Development can easily take place
on the EBDK platform and thereafter
the implementation of the full
Bluetooth capability can be setup by
developed SW/HW and the Bluetooth
module.

Software (HCIdriver, L2CAP,
RFCOMM and SDP) will be available
in source code for PC.

•

HCIdriver – implements the HCI

command driver used by the host

•

L2CAP – handles protocol

multiplexing, segmentation and

re-assembly of packets

•

RFCOMM – provides a serial port

emulation over the L2CAP

protocol

•

SDP – Service Discovery Protocol

provides information on the

services available on a Bluetooth

device

Technical support is available from
the EBDK distributor. Please contact
Ericsson Microelectronics for order-
ing and information regarding the

EBDK and regarding extra daughter
board with ROK 101 007 as add-on
to the EBDK.

Ericsson Bluetooth Starter Kit (EBSK)

A very small convenient kit, which
preferably is used in point-to-
multipoint configuration designs,

based on the Bluetooth module ROK
101 007.

Please contact Ericsson Microelec-
tronics for ordering and information
regarding the Ericsson Bluetooth
Starter Kit.

B ase Band Board

Application Board

Radio Board

JTAG

I2C

A udio

USB

Monitoring pins

RS-232

RS-232

RS-232

Ericsson BaseBand

Ericsson Radio

Module

Address / Data / Control

USB9602

MS7540

Radio Board (0dBm)

Er icsson Radio

Module

R adio Board (20dB m)

Er icsson Radio

Module

optional external antenna 

GLUE LOGIC (XLI NX)

LEDS

Memor y

Memory

EBDK

Audio

RS-232

USB

Ericsson Bluetooth

Module ROK 101 007/1 

Codec

Power

DC/DC

Level-

shift

EBSK

Figure B1. Ericsson Bluetooth Development Kit (EBDK)

Figure B2. Ericsson Bluetooth Starter Kit (EBSK)

Summary of Contents for ROK 101 007






















Reviews:

No comments