Ergotron StyleView SV40 Manual Download Page 11

888-24-257-G-00 rev. D • 06/19 

11 of 13

1

5

6

2

3

4

1

5

2

4

3

Ergonomics

Working

customize - to your size

1 Set top of monitor screen about one inch below eye level - Release brake and lift or lower riser 
as needed.

2 Tilt screen for comfortable viewing and to reduce eye and neck strain.

3 Pull keyboard tray forward and position mouse tray on right or left, as needed.

4  Work with elbows bent at about 90° to minimize muscle strain.

5 If the riser moves up and down with diffi

  culty, or if it drifts out of set position, consult the product 

manual for adjustment information.

6 Stay in charge!
Powered carts should be plugged into outlet as often as possible to keep battery charged and 
computer running.

Moving

stow - before you go

1 During normal movement, release brake and lower worksurface to lowest 
position for optimal stability and unobstructed view.

2 Tuck away open trays and return mouse, scanner and other accessories 
to their places.

3 Unlock both front casters.

4 Push cart from rear with elbows bent at about 90° to maximize control 
and minimize muscle strain.

5 Don’t run out!
Before moving, make sure cord is unplugged from outlet and hooked to 
basket for safe travel.  Remember, charge battery fully 100% every day!

Maintenance & Safety

Hazard Symbols Review 

The Meaning of Symbols appearing in this Guide, on the 
Cart or on the Power System
These symbols alert you to a safety condition that 
demands your attention. You should be able to recognize 
and understand the signifi cance of the following Safety 
Hazards if you encounter them on the Cart or within Cart 
documentation such as this Set-up Guide.

Symbol

 

Signal Word/

Color

Level of Hazard

DANGER

Indicates an imminently hazardous situation which, if not 
avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not 
avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not 
avoided, may result in minor or moderate injury.

CAUTION

Used without the safety alert symbol indicates a potentially 
hazardous situation which, if not avoided, may result in 
property damage.

INSTRUCTIONS

Follow operating instructions.

INSTRUCTIONS

Follow operating instructions.

POWER

"ON" / "OFF" (push-push)
NOTE: Each position "ON" / "OFF" is a stable position.

Summary of Contents for StyleView SV40














Reviews: