manualshive.com logo in svg

ErgoPack Air 713-580, Original Operating Instructions, Page: 13 / 63

Share
Download
ErgoPack Air 713-580 Original Operating Instructions Download Page 13

Warning!

  

Following hazards can result in serious injuries: 

Breaking strap, risk of injury 

When being tensioned, the strap may break and rip. Do not stand 
in line with the strap and wear eye protection. 

Strap ends snapping back, risk of injury 

When  cutting the strap, hold the upper portion and stand aside. 
Do not stand in line with the strap and wear eye protection. 

Supporting ChainLance, risk of tripping 

If the system will be parked, the supporting ChainLance has to be 
fully retracted. The supporting ChainLance must not protrude from 
the system. 

Strap waste, risk of tripping 

Make sure any strap waste or pieces of strap, which possibly 
appeared, will be removed from the floor quickly. 

Sealing head and ChainLance, risk of crushing 

Do  not put your fingers into the area of the tension wheel of the 
sealing head and into the ChainLance.

 

Reversing sledge, risk of crushing 

Especially around the entire surroundings of the reversing sledge, 
there is a risk of squeezing. 

Hazardous area, risk of crushing and risk of injury 

Make sure before each strapping cycle, that there is no person in 
the hazardous area (especially of the ChainLance) and nobody can 
enter that area. This is due, especially for the limited or bad visible 
area on the opposite site of the pallet (operators view). During 
strapping, there must not be any hands or other body parts 
between strap and goods. 

Power source, risk of injury

 

Before maintenance or repair works: 
Switch off the strapping system by pressing the „OFF“ switch, 
remove the key from the main switch and unplug the main power 
cable from the battery pack. 

EX areas, risk of explosion 

The strapping system must not be used in areas with explosive 
atmospheres.

 

-13- 

Summary of Contents for Air 713-580
































































Reviews:

No comments