Direction of rotation
was successfuly
changed
Press UP
for 1s
Moves down
Press UP + DOWN
for 2s
1x run up
and down
Next:
Set lower
end position
Press UP
for 1s
Moves up
Move to requested
end position
Press UP + STOP
for 2s
2x runs up and down,
3x signal tones
C
Set end positions
ATTENTION!
Motor moves to continuous operation after longer keystroke! Urgently stop before reaching the end position
and then proceed through a tip..
For adjusting the end positions see
A
„Fine adjustment of the end positions“!
Set upper end position
Set lower end position
D
Change operation mode to jog mode
Operating in jog mode: The motor moves to continuous operation after 2 sec. of key pressing. Repeat the programming step
to switch back to continuous operation.
E
Change speed
F
Set intermediate positions/ stops
Setting custom stop position
Approach custom stop position
Remove custom stop position
End positions must be set!
G
Remote control and channels
Add remote control or channel
A motor can store up to 10 remote control channels, learning further channels is rejected by the motor.
Delete remote control or channel
Note:
A
is the already programmed remote control,
B
is the new remote control which has to be programmed!
Note:
A
and
B
are the already programmed remote controls,
B
is the remote control which has to be programmed!
H
Factory reset
Next:
Set/change direction
of rotation
Press P1
for 2s
1x run up
and down
Release
P1
1x signal
tone
Press STOP
for 2s
2x runs up and down,
3x signal tones
B
Basic settings
Only necessary for motor replacement or after factory reset.
For adjusting the end positions see
A
„Fine adjustment of the end positions“!
If there is an already programmed remote control, continue with
G
„Remote control and channels“.
Confi guring remote control
Set/change direction of rotation
1x run up and down,
1x signal tone
Jog mode
Continuous operation
2x run up and down,
3x signal tone
Press UP + DOWN
for 5s
1x run up
and down
Press STOP
for 2s
Lower end
position is set
Press DOWN
for 1s
Moves
down
Move to requested
end position
Press DOWN+ STOP
for 2s
2x runs up and down,
3x signal tones
Press P2
for 1s
1x run up and down,
1x signal tone
Press UP
for 1s
1x run up and down,
1x signal tone
Press UP
for 1s
2x run up and down,
1x signal tone
faster
slower
Press DOWN
for 1s
1x run up and down,
1x signal tone
Press DOWN
for 1s
2x run up and down,
1x signal tone
I
Malfunctions and troubleshooting
Error
Cause
Solution
Motor is not
moving
a) The battery is empty.
a) Charge the battery.
b) The battery is charging, but not moving.
b) Battery was deeply discharged, wait for certain state of charge.
c) The remote control is not trained.
c) Follow programming step B.
d) P1 programming button is pressed but no reaction.
d) The motor is defect, contact sun protection specialist.
Blind will move to the
intermediate stop.
Press
STOP 3s
Intermediate
stop is set
Move to the
intermediate
stop
Press
P2 for 1s
1x run up and
down,
1x signal tone
Press
STOP for 1s
1x run up and
down,
1x signal tone
Press
STOP for 1s
2x run up and
down,
3x signal tone
A
A
B
Remote control B
has been deleted
Press
P2 for 1s
1x run up and down,
1x signal tone
Press
P2 for 1s
1x run up and down,
1x signal tone
Press
P2 for 1s
2x run up and down,
3x signal tone
Intermediate stop
is removed
Press
P2 for 1s
1x run up and down,
1x signal tone
Press
STOP for 1s
1x run up and down,
1x signal tone
Press
STOP for 1s
1x run up and down,
1x signal tone
The motor has been reset
to factory settings
Press
P1 for 1s
4x runs up and down
Release
P1
4x signal tone
A
A
B
Remote control B
has been added
Press
P2 for 1s
1x run up and down,
1x signal tone
Press
P2 for 1s
1x run up and down,
1x signal tone
Press
P2 for 1s
2x run up and down,
3x signal tone
