background image

Class 3B Laser Lighting Effect User Safety Guide ProLight Concepts Limited

Installation and Operation Notes

 

1. The laser should only be installed and operated by those that are aware of how

 

     to operate laser, and what the various controls perform. The keyswitch provided

 

     on the laser should help to prevent use by unintended people.

 

2. The laser should be mounted in a suitable and secure position in the venue, so

 

    that once in position it is unlikely to be affected by unintended movement.

 

3. Prior to installation and operation of the laser, the paths of the beams and

 

    effects should be considered, particularly with respect to how they will touch the

 

    audience. If direct audience scanning is desired then the laser energy in the

 

    effects needs to be considered to decide if the effects are safe for direct

 

    viewing.

Introduction

Laser lighting products are used to create some of the most vivid and striking visual effects, and 

are often noted for how they seem to produce solid shapes that cut through the air, and pick up 

highly defined swirling smoke patterns. The light that is used to create these stunning effects is 

different from normal light and therefore several precautions need to taken when using lasers to 

ensure that the lighting effects are safe and enjoyable to view. The optical power output from the 

kind of lasers used for lighting displays can be harmful if not properly setup or is misused. But 

when used following the recommended health and safety guidelines, laser lighting effects no more

harmful than looking at any conventional lighting effect.

This guide has been put together to provide you with some background information about laser 

safety, and guidance on the recommended health and safety requirements for using lasers in 

public places. Although this guide covers the main points to consider when using laser effects, 

users are advised to familiarise themselves with other guidance, particularly that issued by the 

Health and Safety Executive, HS(G)95 The Radiation Safety Of Lasers Used For Display 

Purposes, which is freely downloadable from the HSE website. Attending one of the laser safety 

training courses, listed at the end of this guide, is also highly recommended.

 Equinox Lexor Laser 

 

 

 

 

 

 

 

 

   

     Safety

Important Warnings

Class 3B Lasers have the potential to harm eyesight if viewed directly in the face, and 

in many instances this may be the case, even if viewed over longer distances of several 

tens of metres. Therefore before using the laser product you should familiarise yourself 

with its operation, and also the safety aspects that need to be considered.

Laser lighting effects are quite safe to watch if installed and used correctly, and being 

aware of a few basic factors will help you to achieve this. This guide has been prepared to 

help provide a basic backgrounder to the key safety aspects, and is based on current UK 

health and safety guidance on the use of lasers for public displays.

Summary of Contents for Lexor


















Reviews: