Equalizer FA1TM Operator'S Instruction Manual Download Page 7

Page: 7 / 18

OPERATOR INSTRUCTION MANUAL

IM_FA1TM_Rev08_A4

FA1TM

FLANGE ALIGNMENT TOOL

ACTUATING THE FA1TM

Carry out the Flange Misalignment Determination

Procedure (see Section 3) to determine the points of

maximum misalignment.
In this example the points of maximum misalignment

are the top and bottom of the joint.

POINT OF MAX.

MISALIGNMENT

POINT OF MAX.

MISALIGNMENT

Guide the lift hook into the bolt-hole at the point of

maximum misalignment.

Adjust the drop leg down onto the pipe by slackening

the release knob in an anticlockwise direction.

The tool should be held up level within the bolt-hole

during adjustment. NB: The tool must be parallel to

pipe during operation.

DROP LEG

RELEASE

KNOB

LIFT HOOK

PARALLEL

The drop leg release knob is then tightened until

firm.

Rotate the crank handle clockwise until the driven

wedge makes contact with the opposite flange.

CRANK

HANDLE

DRIVEN

WEDGE

OPPOSITE FLANGE

Thread the strap through the aperture on the base

of the drop leg as shown.

STRAP

APERTURE

Feed the open end of the strap through the buckle

mechanism as shown.

Close the clasp to secure strap.

FEED THROUGH

STRAP

Summary of Contents for FA1TM



















Search results

Summary of Contents for FA1TM

Reviews:

Related manuals for FA1TM

Brands by name

Popular brands

Equalizer FA1TM, Operator'S Instruction Manual

Search results

Summary of Contents for FA1TM

Reviews:

Related manuals for FA1TM

Brands by name

Popular brands