Equalizer Express DTA1007 User Manual Download Page 4

DW9116  Charger

The DW9116 battery charger is designed to use standard household 

120 volt AC 60 Hz power. The use of other power sources like, but 

not limited to, those that convert DC to AC is not recommended and  

will destroy  the internal circuitry of the DW-9116 charger. 

If you do 

not use standard household 120 volt AC, 60 Hz power then only use 

a true sine wave inverter.

DW9109  12-Volt Automotive Charger

The DW9109 battery charger is designed to plug into the cigarette 

lighter or power point of a vehicle and use 12 volt DC power. Do not 

use AC power. The use of any other power source, such as a device 

to convert AC to DC power, is not recommended and may cause 

serious damage to the circuitry of the DW-9109 charger.

Charging Procedure

1.  Plug the charger into an appropriate power outlet.
2.  Insert the battery pack into the charger, as  shown in

     Fig. 1 and Fig. 2, making sure the pack is fully seated in    

     the charger. The red (charging) light will blink continously,  

     indicating that the charging process has started.
3.  The battery pack will be fully charged in about 1

     hour. The completion of charge will be indicated by   

     the red light remaining ON continuously. The pack is    

     fully charged and may be used at this time or left in the charger.

Battery Use and Care

Take care when loading the battery into the tool.  Do NOT 

slam the battery into the Equalizer

®

 Express

®

 tool.  

Gently 

press the battery into place. 

Depending on cutting conditions 

and operator skill, a fully charged battery should remove about 

three windshields.  

The batteries are the most sensitive part of the Equalizer

® 

Express

®

 tool. Please, carefully read these detailed instructions 

about proper battery charging and care.

Fig. 2

Fig. 1

Battery (DeWalt D)

Read this very carefully!

  There are sev-

eral off-the-shelf batteries that will fit the 

Equalizer

®

 Express

®

. This toolʼs battery 

is a DeWalt D and it feeds 

electricity to the motor and runs it back-

wards so it will stop quickly. 

Other batter-

ies will feed too much electricity into the switch and can cause 

the drive mechanism to unwind. Some do not send enough and 

can cause the switch to be destroyed.

 The threads are clockwise 

and when too much counterclockwise force is applied the threads 

can unscrew, freeze the tool and cause permanent damage. Use 

only DeWalt D batteries.

Important Safety Instructions About the 

Battery  and Chargers 

Warning: When using the Equalizer

®

 Express

®

 there are basic 

safety precautions that should be followed to reduce risk of 

fire, electric shock and personal injury, including the following:

 Do not incinerate the battery pack even if it is severely 

   damaged or is completely worn out. The battery pack can    

   explode in a fire.

 A small leakage of liquid from the battery pack cells may    

   occur under extreme usage or temperature conditions. This  

   does not indicate a failure. However, if the outer seal is broken  

   and this leakage gets on your skin--

   

A. Wash quickly with soap and water.

    

B.  Neutralize with mild acid such as lemon juice or vinegar.

    C.  If battery liquid gets into your eyes, flush them with

         clean water for a minimum of 10 minutes and seek 

         immediate medical attention.
(Medical Note: The liquid is a 25%-30% solution of potassium 

hydroxide.)

 Never attempt to open the battery pack for any reason. If the  

   plastic housing of the battery pack breaks or cracks, immedi 

   ately discontinue use and do not recharge.

  Do not carry extra, charged battery packs in aprons, pockets, or  

   tool boxes along with other metal objects. Battery pack could  

   be short circuited, causing damage to the battery pack and pos 

   sibly causing severe burn or fire.

Tune-Up  Procedure

At the end of every two weeks, completely discharge your bat-

tery. Batteries can develop a memory which will shorten the 

working time they can be used. The tune-up procedure will 

eliminate the memory build-up.
1. Hold or tie down the trigger & let the tool run until it stops.

     

2. Wait 20 minutes then repeat (tool will only run a    

 

     short time the second time).
 3. Allow the battery to cool completely, then  

 

 

     recharge.

Important Instructions For Your Equalizer

®

 Express

®

 18-Volt Battery& Charger

Equalizer

®

 Express

®

4

Reviews: