background image

14

TROUBLESHOOTING

P13/H3

(

High pressure abnormal error(In heating mode)

)

Diagnosis

Handling

P14

(High compression ratio protection)

Diagnosis

Handling

P15

(Low compression ratio protection)

Diagnosis

Handling

Check if the liquid side of
outdoor system is blocked

Remove dirty and keep it unobstructed

Check if there is too much
Air or N2 in the system

No

Discharge the refrigerant,
vacuum, recharge refrigerant

Yes

Power off and re-power on
to see whether it is normal

If there is still abnormal

replace the mainboard

No

Yes

Yes

Check if the refrigerant is lack
or

the

refrigerant

is

No

Charge some refrigerant into the system

Yes

Check if there is too much
Air or N2 in the system

Discharge the refrigerant,
vacuum, recharge refrigerant

Power off and re-power on to
see whether it is normal

Check if the throttle part of
the system is blocked

Remove dirty and keep it unobstructed

If there is still abnormal

replace the mainboard

No

No

Yes

Yes

Yes

Yes

Power off and re-power on
to see whether it is normal

No

If there is still abnormal

replace the mainboard

Check if the throttle part of
the system is blocked

Remove dirty and keep it unobstructed

Summary of Contents for 18S-EHVC WD2H Series


















Reviews: