background image

TM-T83 User’s Manual

3

English

Important Safety Information

This section presents important information intended to ensure safe and effective 
use of this product. Read this section carefully and store it in an accessible location.

Key to Symbols

The symbols in this manual are identified by their level of importance, as defined 
below. Read the following carefully before handling the product.

WARNING:

Warnings must be observed carefully to avoid serious bodily injury.

CAUTION:

Cautions must be observed to avoid minor injury to yourself, damage to your 
equipment, or loss of data.

Safety Precautions

This section describes the warnings and cautions intended to ensure safe and 
effective use of the TM-T83. Other warnings and cautions on handling of this 
product for its safe and effective use are described in other sections of the manual.

WARNING:

If the TM-T83 produces smoke, a strange odor, or unusual noise, shut down the TM-
T83, unplug the power cable immediately, and then contact your dealer or an 
Epson service center for advice. Continued use may lead to fire or electric shock.
Never attempt to repair this product yourself. Improper repair work can be 
dangerous.
Never disassemble or modify this product. Tampering with this product may 
result in injury or fire.
Be sure to use the specified power source. Connection to an improper power 
source may cause fire.
Do not allow foreign matter to fall into the equipment. Penetration by foreign 
objects may lead to fire.
If water or other liquid spills into this equipment, shut down the TM-T83, unplug 
the power cable of the TM-T83 immediately, and then contact your dealer or 
an Epson service center for advice. Continued use may lead to fire or shock.
If you open the DIP switch cover, be sure to close the cover and tighten the 
screw after adjusting the DIP switch. Using this product with the cover open 
may cause fire or electric shock.

Do not use aerosol sprayers containing flammable gas inside or around this 
product. Doing so may cause fire.

Do not connect a telephone line to the drawer kick-out connector; otherwise, 
the printer and the telephone line may be damaged.

CAUTION:

Do not connect cables in ways other than those mentioned in this manual. 
Different connections may cause equipment damage or fire.
Be sure to set this equipment on a firm, stable, horizontal surface. The product 
may break or cause injury if it falls.
Do not use this product in locations subject to high humidity or dust levels. 
Excessive humidity and dust may cause equipment damage or fire.

Summary of Contents for TM-T83













Reviews: