Epson Stylus Pro 9700 Series User Manual Download Page 182

Page: 182 / 228

182

182

Solving Problems

Auto Take-Up Reel Error Messages

If you have the optional Automatic Take-Up Reel System, check the
following list for error messages that might appear:

Improving Print Quality

You can often improve print quality by doing the following:

•

Run a nozzle check and cleaning cycle. See page 152 for instructions.

•

Align the print head. See page 156 for instructions.

•

When you send a print job, make sure your print options are set
correctly. For more information, see page 85 (Windows) or page 111
(Macintosh).

Message

Explanation

Response

TAKE-UP DISCONNECTED

SET AUTO TAKE-UP REEL
SYSTEM IN PRINTER AND
RESTART THE PRINTER

The Auto Take-up Reel is not
installed correctly.

Turn the printer off, then install the Auto
Take-up Reel correctly. See page 203.

TAKE-UP DISCONNECTED

AUTO TAKE-UP REEL UNIT
IS DISCONNECTED

DO YOU CONTINUE?
NO
YES

The Auto Take-up Reel is not
installed correctly.

Select

YES

to continue printing without

using the Auto Take Up Reel. Or, select

turn the printer off, then connect the Auto
Take-up Reel (see page 203) and restart the
printer.

TAKE-UP ERROR

CHECK THE STATUS OF
AUTO TAKE-UP REEL UNIT
AND RESTART THE
PRINTER

Paper is not loaded on the reel
correctly.

Press the

button and load the paper

correctly; see page 204.

TAKE-UP ERROR

IS ANYTHING
OBSTRUCTING THE
TAKE-UP REEL SENSOR
SYSTEM?

LOAD PAPER AGAIN

The Auto Take-up Reel is not
winding paper.

Make sure nothing is obstructing the
sensor. Press the

button and load the

paper correctly; see page 204.

Summary of Contents for Stylus Pro 9700 Series





































































































































































































































Search results

Summary of Contents for Stylus Pro 9700 Series

Reviews:

Brands by name

Popular brands

Epson Stylus Pro 9700 Series, User Manual

Search results

Summary of Contents for Stylus Pro 9700 Series

Reviews:

Brands by name

Popular brands