manualshive.com logo in svg

Epson Stylus Pro 9700 Series, User Manual

Share
Download
Epson Stylus Pro 9700 Series User Manual Download Page 203

203

203

If you want to print multiple images on roll paper and have the printouts 
rolled up automatically, you can use the optional Auto Take-Up Reel 
(Epson Stylus Pro 9700 only).

To install the Auto Take-Up Reel, follow the instructions in the manual that 
came with it.

You can wind your printed media either forward (with the printed surface 
outside), or backward (with the printed surface inside).

The table below describes the status of the Auto Take-Up Reel as indicated 
by the 

Sensor

 light.

Sensor light status

Description

On

Ready to use.

Flashing rapidly

Operating

Flashing slowly

Power-saving mode

Flashing very slowly

The Auto Take-Up Reel has an error and stopped 
working; check the installation and see page 193 for 
additional solutions.

Off

Turned off.

Appendix B: 
Using the 
Optional Auto 
Take-Up Reel

Note: 

Epson 

Doubleweight or 
Singleweight Matte paper 
should be wound forward.

Winding forward

Winding backward

Sensor 
light

Summary of Contents for Stylus Pro 9700 Series





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands