manualshive.com logo in svg

Epson SC-S40600 Series, User Manual

Share
Download
Epson SC-S40600 Series User Manual Download Page 6

Introduction

Printer Parts

Front Section

The illustration shows the SC-S60600 Series.

A

Maintenance cover (left)

Open this cover to clean the area around the print head. Normally closed when using the printer.

U

 

“Cleaning Around the Print Head” on page 67

B

Additional Print Drying System

The heater can be used to rapidly dry ink after printing. This is an option for the SC-S80600 Series/SC-S80600L
Series/SC-S40600 Series.

U

 

Additional Print Drying System Setup Guide

C

After heater

The heater can be used to rapidly dry ink after printing.

U

 

“Changing the Heater Temperature and Drying Settings” on page 55

D

Tension bar

The tensioner maintains tension to prevent the media sagging as it is taken up.

U

 

“Using the Auto Take-up Reel Unit” on page 36

SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series     User's Guide

Introduction

 

6

Summary of Contents for SC-S40600 Series






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands