background image

5.  FUNCTIONAL DESCRIPTION 
 

 

14

 

EPSON

 

S1S65010

 

Evaluation Board Technical Manual (Rev. 1.1e)

 

5.3. Hardware Reset Switch (SW3) 

(3) in Figure 5.1 

This switch (SW3) is available for user application systems using hardware resets. 

 
 

5.4. CF Card CFOE#/CFRST Select Switch (SW8) 

(4) in Figure 5.1 

The (SW8) switch on this board configures the CFOE# and CFRST outputs to the CF card interface. The 
following Table describes the three configurations available. 
If the user application system does not use CF cards, set this to the OFF position. Otherwise, set as C = 

c

, C = 

c

The default setting is OFF. 

 

Display 

Position 

CFOE# (CF card input) 

CFRST_CN (CF card input) 

Notes 

c

 

MOE# (S1S65010 output) 

CFRST (S1S65010 output) 

 

OFF NC 

NC 

 

d

 

GND RESET# 

(HW-RESET) 

 

 
 

5.5. Memory Chip Select Switch (SW5) 

(5) in Figure 5.1 

This board includes Flash ROM and SRAM for use as external memory. The (SW5) switch on this board 
configures their chip select signals. The following Table describes the three configurations available. 
The default setting is 

c

.

 

 

Display 

Position 

MCSB# (SRAM CS#) 

MCSA# (Flash ROM CS#) 

Notes 

c

 

MCS1# (S1S65010 output) 

MCS0# (S1S65010 output) 

 

OFF NC 

NC 

 

d

 

MCS0# (S1S65010 output) 

MCS1# (S1S65010 output) 

 

 

The following is a close-up view of the switches used in Sections 5.4 and 5.5 above. They each offer three 
settings: 

c

d

, and OFF. 

 

SW

8

1

2

 

 
 

5.6. Connection Switch for nSRST from JTAG In-Circuit Emulator (SW2) 

(6) in Figure 5.1 

The (SW2) switch on this board controls the use of the nSRST signal from the JTAG in-circuit emulator as a 
system hardware reset signal. 
The default setting is ON. Change this to OFF as necessary. 

 

Summary of Contents for S1S65010









































Reviews: