Epson S1C33L26 Technical Manual Download Page 421 | Manualshive

Page: 421 / 722

background image

25 A/D CONVERTER (ADC10)

S1C33L26 TECHNICAL MANUAL

Seiko Epson Corporation

25-3

3.1.1 A/D Conversion Clock (PCLK1 Division Ratio) Selections

Table 25.

ADDF[3:0]

Division Ratio

0xf

Reserved

0xe

1/32768

0xd

1/16384

0xc

1/8192

0xb

1/4096

0xa

1/2048

0x9

1/1024

0x8

1/512

0x7

1/256

0x6

1/128

0x5

1/64

0x4

1/32

0x3

1/16

0x2

1/8

0x1

1/4

0x0

1/2

(Default: 0x0)

Selecting A/D Conversion Start and End Channels

25.3.2

Select the channel in which the A/D conversion is to be performed from among the pins (channels) that have been
set for analog input. To enable A/D conversions in multiple channels to be performed successively through one con-
vert operation, specify the conversion start and conversion end channels using ADCS[2:0]/ADC10_TRG register
and ADCE[2:0]/ADC10_TRG register, respectively.

3.2.1 Relationship between ADCS/ADCE and Input Channels

Table 25.

ADCS[2:0]/ADCE[2:0]

Channel selected

0x7–0x6

Reserved

0x5

AIN5

0x4

AIN4

0x3

AIN3

0x2

AIN2

0x1

AIN1

0x0

AIN0

(Default: 0x0)

Example: Operation of one A/D conversion

ADCS[2:0] = 0, ADCE[2:0] = 0

Converted only in AIN0

ADCS[2:0] = 0, ADCE[2:0] = 3

Converted in the following order: AIN0

→

AIN1

→

AIN2

→

AIN3

ADCS[2:0] = 4, ADCE[2:0] = 1

Converted in the following order: AIN4

→

AIN5

→

(AIN6)

→

(AIN7)

→

AIN0

→

AIN1

Note: The control circuits in the A/D converter supports up to eight channels for expansion in the future,

and  it  performs  A/D  conversion  if  a  channel  (AIN6–AIN7)  without  an  analog  input  is  specified.
In  this  case,  the  results  that  will  be  stored  to  ADD[15:0]/ADC10_ADD  register  is  0x0. To  avoid
A/D  conversion  for  the  channels  without  an  input,  set  the  ADCS[2:0]  to  equal  or  smaller  than
ADCE[2:0] within the available analog inputs.

«
...
419
420
421
422
423
...
»

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Brand: Badger Meter Pages: 20

ROBO Cylinder RCP2 Series

Brand: IAI Pages: 5

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: Olsen Pages: 4

Tunnel Master Jr

Brand: ICS Pages: 70

Brand: Danfoss Pages: 14

Brand: TAC Pages: 76

Brand: Sturtevant Richmont Pages: 73

SW-HBT4K-C6-4X4E

Brand: Avenview Pages: 8

Brand: adept technology Pages: 96

Brand: Rain Bird Pages: 7

Brand: Technische Alternative Pages: 124

NetworkHD 200 series

Brand: Wyrestorm Pages: 4

Brand: Tech Controllers Pages: 20

Brand: i4Home Pages: 2

Brand: Watt Stopper Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands