manualshive.com logo in svg

Epson S1C33L26, Technical Manual

The Epson S1C33L26 Technical Manual is here to assist you in understanding the functionality and features of this incredible product. Easily accessible for download, for free, from our website, it provides comprehensive instructions and insights to maximize your experience with the Epson S1C33L26.

Share
Download
background image

20  GENERAL-PURPOSE SERIAL INTERFACE (FSIO)

20-28

 

Seiko Epson Corporation 

S1C33L26 TECHNICAL MANUAL

D2 

IRRL: IrDA I/F Input Logic Inversion Bit

 

Inverts the logic of the IrDA input signal.

 

1 (R/W):  Inverted 

 

0 (R/W):  Not inverted (default)

 

When using the IrDA interface, set the logic of the signal that is input from an external infrared-ray 
communication circuit to the chip to suit the serial interface. If IRRL is set to 1, a high pulse is input as 
a logic 0. If IRRL is set to 0, a low pulse is input as a logic 0.

D[1:0] 

IRMD[1:0]: Interface Mode Select Bits

 

Selects the IrDA interface function. 

10.5  IrDA Interface Setting

Table 20.

IRMD[1:0]

Interface mode

0x3

Setting prohibited (reserved)

0x2

IrDA 1.0 interface

0x1

Setting prohibited (reserved)

0x0

Normal interface

(Default: 0x0)

 

When using the IrDA interface function, write 0x2 to IRMD[1:0] while setting to asynchronous mode 
for the transfer mode. If the IrDA interface function is not to be used, write 0x0 to IRMD[1:0]. 

Note:  This selection must always be performed before the transfer mode and other conditions are 

set.

FSIO Ch.

x

 Baud-rate Timer Control Registers (FSIO_BRTRUN

x

)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

FSIO Ch.

x

 

Baud-rate Timer 
Control Register
(FSIO_
BRTRUN

x

)

0x300705
0x300715

(8 bits)

D7–1 –

reserved

–

–

–

0 when being read.

D0

BRTRUN

Baud-rate timer run/stop control

1 Run

0 Stop

0

R/W

D[7:1] 

Reserved

D0 

BRTRUN: Baud-rate Timer Run/Stop Control Bit

 

Controls the baud-rate timer’s RUN/STOP states.

 

1 (R/W):  Run

 

0 (R/W):  Stop (default)

 

The baud-rate timer loads the reload data (BRTRD[11:0]/FSIO_BRTRDL

x

 and FSIO_BRTRDL

x

 reg-

isters) to its counter and starts counting down when 1 is written to BRTRUN. The baud-rate timer stops 
counting when 0 is written to BRTRUN.

FSIO Ch.

x

 Baud-rate Timer Reload Data L Registers (FSIO_BRTRDL

x

)

FSIO Ch.

x

 Baud-rate Timer Reload Data H Registers (FSIO_BRTRDH

x

)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

FSIO Ch.

x

 

Baud-rate Timer 
Reload Data L 
Register
(FSIO_
BRTRDL

x

)

0x300706
0x300716

(8 bits)

D7–0 BRTRD[7:0] Baud-rate timer reload data [7:0]

0x0 to 0xff

(BRTRD[11:0] = 0x0 to 0xfff)

0x0 R/W

FSIO Ch.

x

 

Baud-rate Timer 
Reload Data H 
Register
(FSIO_
BRTRDH

x

)

0x300707
0x300717

(8 bits)

D7–4 –

reserved

–

–

–

0 when being read.

D3–0 BRTRD

[11:8]

Baud-rate timer reload data [11:8]

0x0 to 0xf

(BRTRD[11:0] = 0x0 to 0xfff)

0x0 R/W

D[7:0]/FSIO_BRTRDL

x

, D[3:0]/FSIO_BRTRDH

x

 

BRTRD[11:0]: Baud-rate Timer Reload Data [11:0]

 

Sets the initial counter value of the baud-rate timer. (Default: 0x0)

Summary of Contents for S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33L26

Panasonic FP2 Series Technical Manual preview
FP2 Series
Brand: Panasonic Pages: 68
Panasonic FP0H Series Operation Manual preview
FP0H Series
Brand: Panasonic Pages: 20
GAUGEMASTER COMBI Manual preview
COMBI
Brand: GAUGEMASTER Pages: 2
EasyIO FC Series Firmware Upgrade User Manual preview
FC Series
Brand: EasyIO Pages: 19
PAC 212 Install Manual preview
212
Brand: PAC Pages: 17
FAAC E124 Original Instructions Manual preview
E124
Brand: FAAC Pages: 44
IAI Msep First Step Manual preview
Msep
Brand: IAI Pages: 5
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Brand: Raypak Pages: 24
J+J S 20 Handbook preview
S 20
Brand: J+J Pages: 91
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
J+J J4C Series Installation Instructions preview
J4C Series
Brand: J+J Pages: 2
Full Gauge Controls MT-543Ri LOG Manual preview
MT-543Ri LOG
Brand: Full Gauge Controls Pages: 3
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Brand: TEL Pages: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Brand: Vimar Pages: 32
Adaptec ACB-2310 Installation Manual preview
ACB-2310
Brand: Adaptec Pages: 2
Velleman CHLSC2 User Manual preview
CHLSC2
Brand: Velleman Pages: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Brand: National Instruments Pages: 27
Sysmac CQM1 Operation Manual preview
CQM1
Brand: Sysmac Pages: 159

Brands by name

Popular brands

Load more brands