Epson S1C31D50 Technical Instructions Download Page 119

Page: 119 / 472

9-4

Seiko Epson Corporation

S1C31D50 TECHNICAL MANUAL

(Rev. 1.00)

9.4.

Control Registers

WDT2 Clock Control Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

WDT2CLK

–

0x00

–

DBRUN

R/WP

–

0x0

–

CLKDIV[1:0]

0x0

R/WP

–

0x0

–

CLKSRC[1:0]

0x0

R/WP

Bits 15

–

Reserved

Bit 8

DBRUN

This bit sets whether the WDT2 operating clock is supplied in DEBUG mode or not.

1 (R/WP): Clock supplied in DEBUG mode
0 (R/WP): No clock supplied in DEBUG mode

Bits 7

–

Reserved

Bits 5

–

CLKDIV[1:0]

These bits select the division ratio of the WDT2 operating clock (counter clock). The clock
frequency should be set to around 256 Hz.

Bits 3

–

Reserved

Bits 1

–

CLKSRC[1:0]

These bits select the clock source of WDT2.

Table 9.4.1 Clock Source and Division Ratio Settings

WDT2CLK.

CLKDIV[1:0] bits

WDT2CLK.CLKSRC[1:0] bits

0x0

0x1

0x2

0x3

IOSC

OSC1

OSC3

EXOSC

0x3

1/65,536

1/128

1/65,536

1/1

0x2

1/32,768

0x1

1/16,384

0x0

1/8,192

(Note) The oscillation circuits/external input that are not supported in this IC cannot be

selected as the clock source.

Summary of Contents for S1C31D50

























































































































































































































































































































































































































































































Search results

Summary of Contents for S1C31D50

Reviews:

Related manuals for S1C31D50

Brands by name

Popular brands

Epson S1C31D50, Technical Instructions

Search results

Summary of Contents for S1C31D50

Reviews:

Related manuals for S1C31D50

Brands by name

Popular brands