Epson RX595 - Stylus Photo Color Inkjet Service Manual Download Page 46

Page: 46 / 131

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Troubleshooting

Troubleshooting When There is Error Display

3.2.3 FATAL Error

C H E C K

P O I N T

The EEPROM stores the error code of the latest fatal error.
The latest fatal error can be identified using the adjustment
program.

Table 3-3. Fatal Errors

Category

Error Code

Error

Cause

Remedy

DC error
(CR motor)

01H

CR PID speed over error

An error occurred in the CR
motor operating sequence

Checking the operation of the Carriage Assy;
Move the Carriage Assy by hand, and check to see if it moves smoothly.

Making the following adjustments

♦

Bi-D

♦

Paper feed length with PF Assy

♦

Paper feed length with Eject Assy

♦

PW adjustment

Checking the following parts and replacing the defective one

♦

Checking the head FFC (CN10/11/12) for disconnection or breakage

♦

Checking the lead wires of the CR Motor (CN14) for disconnection or breakage

♦

Checking the CR Encoder FFC (CN1) for disconnection or breakage

♦

Checking the printer frame for adhesion of dirt or insufficient lubrication

(p.119)

♦

Checking the CR Guide Shaft for adhesion of dirt or insufficient lubrication

(p.119)

♦

Checking the Linear Scale for adhesion of dirt or damage

(p.75)

♦

Checking the CR Encoder for adhesion of dirt or damage

(p.90)

♦

Checking the PW Sensor for adhesion of dirt or damage

(p.90)

♦

Checking the CR Belt for damage or improper tension

(p.88)

♦

Checking the CR Motor and replacing it if necessary

(p.88)

♦

Main Board

(p.66)

♦

Power Supply Board

(p.80)

02H

CR load positioning lock error

08H

CR PID reverse rotation detection error

0AH

CR load positioning accumulation moving
distance error

0BH

CR load positioning speed over error

0CH

CR PID lock error

0DH

CR PID aveTi max error

Summary of Contents for RX595 - Stylus Photo Color Inkjet




































































































































Search results

Summary of Contents for RX595 - Stylus Photo Color Inkjet

Reviews:

Epson RX595 - Stylus Photo Color Inkjet, Service Manual, Page: 46 / 131

Search results

Summary of Contents for RX595 - Stylus Photo Color Inkjet

Reviews: