background image

Epson Stylus NX125/T13/NX130 series

Revision F

Disassembly/Assembly

Details of Disassembling/Assembling by Parts/Unit

16

Confidential

1.3

Details of Disassembling/Assembling by Parts/Unit

Panel Unit (NX125/NX130 series)

Do not lift the Panel Unit too fast, since the Panel FFC is connected 
to the back of the Panel Unit.

Panel Unit

Panel FFC

Document Pad (NX125/NX130 series)

When installing the Document Pad, follow the procedure below.

1. Place the Document Pad with the side where the double-sided 

tape attached upward on the document glass aligning its corner 
with the origin position.

2. Close the Document Cover to attach the Document Pad.

Standard line
Double-sided tape

Document Cover

Document Pad

Origin Position

Scanner Unit (NX125/NX130 series)

Do not lift the Scanner Unit too fast, since the Panel FFC, Scanner Motor cable and Scanner FFC are connected to the rear side of the Scanner Unit.

Tighten the screws in the order indicated in figure above.

3

Panel FFC

Scanner FFC

Scanner Motor cable

Scanner 

Unit

Scanner Unit

1

2

4

C.B.P-TITE SCREW 3x10 (5.0 

±

 0.5 kgf·cm)

CIS (NX125/NX130 series)

Be careful not to lose the Spacer because it comes off easily when disassembling the CIS.

When installing the spacers, be sure to place them with the cutout facing inward.

Align the toothed side of the Timing Belt with the same shaped rib of the backside of the CIS, and secure the Timing Belt with Torsion Spring. 

Spacer

Backside of the CIS

Timing Belt

Torsion Spring

Toothed 

side

CIS

Main Board

Take care not to damage the PE Sensor Lever.

Align the ribs (x3) of the Main Frame with the cutouts of the Main Board.

Main Board

PE Sensor Lever

Rib

Main Board

Summary of Contents for ME 320





































Reviews: