Epson Equity 386/20 Product Support Bulletin Download Page 10 | Manualshive

Page: 10 / 45

background image

Product Support Bulletin

Subject:

Novell Netware Compatibility Test Results for the Equity 386/20

Date:

8/11/88

Page:

1 of 1

PSB No.:

Originator: GLW

This bulletin is intended to provide a summary of the results of compatibility
testing of the Equity 386/20 with Novell local-area networking products. The

Equity 386/20 was tested at 20MHz. This information was provided to Epson by
Novell’s Independent Manufacturing Support Program. For complete test result
reports, contact Novell, Inc.

Terms:

NDFS - Non - Dedicated File Server
NDWS - Non - Dedicated Work Station

Netware Version
Netware Type

Tested as

2.0a

ELS I
NDFS

2.15

2.15

ELS II

ADV 286

NDFS

NDFS

NDFS NDWS

Network Interface

3Com 3C501
3Com 3C503
3Com 3C505/1194
3Com 3C505/2012
AT&T Starlan
Gateway G - Net

IBM PCN II
IBM TRN
Micom Nl5010
Micom NP600
Novell Int NIC
Novell NE1000
Novell NE2000
Novell NL1000
Novell RX- NET
Proteon ProNet

SMC/PD ArcNet

Novell DCB/NE2000

tested as compatible

X

X
X

X

X

X

X

X

X

X

F

failed

< blank > not tested

«
...
8
9
10
11
12
...
»

Summary of Contents for Equity 386/20














































Reviews:

No comments

Related manuals for Equity 386/20

Veriton Hornet N260G

Brand: Acer Pages: 22

Brand: IBM Pages: 160

Brand: EUROCOM Pages: 1

Brand: Arbor Technology Pages: 115

Brand: DFI Pages: 69

Evo Desktop Series

Brand: Compaq Pages: 30

Brand: Dell Pages: 148

Brand: Dell Pages: 18

Brand: Uplift Desk Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 29

PCV-RS422X - Vaio Desktop Computer

Brand: Sony Pages: 1

PCV-RS421 - Vaio Desktop Computer

Brand: Sony Pages: 1

PCV-RS420 - Vaio Desktop Computer

Brand: Sony Pages: 1

PCV-RS411 - Vaio Desktop Computer

Brand: Sony Pages: 1

PCV-RS320 - Vaio Desktop Computer

Brand: Sony Pages: 1

PCV-RS400CG - Vaio Desktop Computer

Brand: Sony Pages: 2

Brand: Sony Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands