Epson EL 33 User Manual Download

Page: 78 / 115

Lotus 1-2-3 or Symphony

If you have not yet installed Lotus 1-2-3 or Symphony, follow

the instructions in your Lotus documentation to install it. Then

follow these steps to install the drivers:

Insert Utility Diskette 1 in drive A.

Type

: and press

Enter

to log onto drive A.

Copy the drivers from

the

Utility Diskette 1 to the Lotus or

Symphony program directory on your hard disk.

If you are installing drivers for 1-2-3 to the C:\LOTUS

directory, type the following and press

Enter:

SET123 C:\LOTUS

If you are installing drivers for Symphony to the

C:\SYMPHONY directory, type the following and press

Enter:

SETSYMPH C:\SYMPHONY

Log onto your Lotus program directory.

Type

INST

and press

Enter to run the

installation

program.

From the main menu, select

Advanced

options and press

Enter.

Then select

Add new drivers to library

and press

Enter.

When the program finishes adding drivers to the library,

select Modify current driver

set and press

Enter.

Installing Video Drivers

5-3

Summary of Contents for EL 33




















































































































Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands

Epson EL 33, User Manual

Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands