Epson C31C514452 Technical Reference Manual Download Page 3 | Manualshive

Page: 3 / 154

Epson C31C514452 Technical Reference Manual Download Page 3

Rev. H

ii

TM-U220 Technical Reference Guide

About This Manual

Aim of the Manual

This manual was created to provide information on the TM-U220 printer for anyone who is
developing hardware, installations, or programs. Programmers will also want to consult other
documents.

Contents of the Manual

Chapter 1, “

General Information

General description of features plus
specifications.

System Planning

Contains introduction of control methods and
each connection form.

Chapter 3, “

Contains information on such matters as DIP
switches, memory switches, error processing for
using TM-U220.

Troubleshooting

Contains useful information for using.

Application Development

Contains useful information for programming.

Notices for Replacement of

the TM-U210/TM-U300

Contains various notices and comparison
information for using the TM-U220 as a
replacement for the TM-U210/TM-U300.

Appendix A, “Comparison table for TM-
U220/U210/U300.”

Comparison table for replacing TM-U210/
TM-U300 with the TM-U220.

Appendix B, “How to Install the Printer on
a Wall with the WH-10.”

Installation instructions.

Appendix C, “Power Supply Unit.”

Describes the external dimensions and
specifications of the power supply units.

Appendix D, “Character Code Table.”

Contains the supported character tables.

«
1
2
3
4
5
...
»

Summary of Contents for C31C514452



























































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands