manualshive.com logo in svg

Epson C31C514452, Technical Reference Manual

Share
Download
Epson C31C514452 Technical Reference Manual Download Page 81

Rev. H

Troubleshooting   

4-1

TM-U220 Technical Reference Guide

Chapter 4

Troubleshooting

This section describes general troubleshooting.

4.1  LED Blinking Pattern

4.1.1  Error Types

The printer stops all printer operations for the selected paper section, goes offline, and the 
ERROR LED blinks when an error is detected.

4.1.1.1  Errors that automatically recover

Note:

(*1) This conditions are selected by MSW 8-5, 8-8. When MSW 8-5 (mapping of the cover open status) is 
off, the error hasn’t occurred but there is a “paper end error” instead. If MSW 8-8 is off, this error is 
handled as an automatically recoverable error.

(* 2) Print head temperature error is not abnormal.

ERROR

Description

ERROR LED Blinking Pattern

  

              

Recovery

Roll paper cover 
open error (when 
recoverable error is 
selected) (*1)

The roll paper cover is 
opened when printing.

Recovers automatically 
when the cover is 
closed. 

Print head 
temperature error (*2)

The temperature of the 
print head is extremely 
high

Recovers automatically 
when the print head 
cools

160 ms

Summary of Contents for C31C514452



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands