Epson Aculaser CX21N Series User Manual Download Page 42 | Manualshive

Page: 42 / 401

background image

Paper Handling

42

Note:

When printing on the back side of previously printed paper, select

Semi-Thick (Back)

.

❏

You can also make these settings on the Setup menu’s Tray Menu on the control panel.
See "Tray Menu" on page 242.

EPSON Color Laser Transparencies

Epson recommends the use of EPSON Color Laser Transparencies.

Note:

Duplex printing is not available for transparencies.

Transparencies can be loaded into the MP tray only. When using transparencies, you
should make paper settings as shown below:

❏

Make settings on the Basic Settings in the printer driver.

❏

You can also make these settings on the Setup menu’s Tray Menu on the control panel.
See "Tray Menu" on page 242.

Please note the following when handling this media:

❏

Hold each sheet by its edges, as oil from your fingers may transfer to the surface and
damage the printable surface of the sheet. The Epson logo appears on the printable
side.

Paper Size:

A4

Paper Source:

MP Tray

(up to 180 sheets or up to 20 mm

thick stack)

Lower Cassette

(up to 500 sheets or up to

56 mm thick stack)

Paper Type:

Semi-Thick

Paper Size:

A4

or

LT

Paper Source:

MP Tray

(up to 75 sheets)

Paper Type:

Transparency

«
...
40
41
42
43
44
...
»

Summary of Contents for Aculaser CX21N Series


















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Aculaser CX21N Series

Brand: DASCO Pages: 2

Brand: quadient Pages: 130

Brand: Oki Pages: 189

Brand: Zebra Pages: 29

Brand: Oki Pages: 255

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: Oki Pages: 18

Brand: Ascend Pages: 6

Brand: Xerox Pages: 18

Brand: Wasp Pages: 2

Brand: Xerox Pages: 240

Brand: Star Pages: 2

Pacemark PM4410

Brand: Oki Pages: 28

CardJet X001200

Brand: FARGO electronics Pages: 52

GSS-LABEL-PTR-M

Brand: EMS Pages: 2

Brand: IBM Pages: 210

Brand: EDNord Pages: 168

Brand: EDNord Pages: 198

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands