manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 168

168

Setting Up Your Printer on a Network

Chapter 5

Setting Up Your Printer on a Network

For Windows

Sharing the printer

This section describes how to share the printer on a standard 
Windows network.

The computers on a network can share a printer that is directly 
connected to one of them. The computer that is directly connected 
to the printer is the print server, and the other computers are the 
clients which need permission to share the printer with the print 
server. The clients share the printer via the print server.

According to the versions of Windows OS and your access rights 
on the network, perform the appropriate settings of the print 
server and clients.

Setting the print server

❏

For Windows Me, 98, or 95, see “Setting up your printer as a 
shared printer” on page 169.

❏

For Windows XP, 2000, NT 4.0, or Server 2003, see “Using an 
additional driver” on page 171.

Setting the clients

❏

For Windows Me, 98, or 95, see “With Windows Me, 98, or 
95” on page 178.

❏

For Windows XP or 2000, see “With Windows XP or 2000” on 
page 179.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands