manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 169

Setting Up Your Printer on a Network

169

5

5

5

5

5

5

5

5

5

5

5

5

❏

For Windows NT 4.0, see “With Windows NT 4.0” on page 
183.

Note:

❏

When sharing the printer, be sure to set EPSON Status Monitor 3 
so that the shared printer can be monitored on the print server. See 
“Setting Monitoring Preferences” on page 101.

❏

When you are Windows shared printer user in a Windows Me, 98, 
or 95 environment, on the server, double-click the 

Network

 icon in 

Control panel and make sure that the “File and printer sharing for 
Microsoft Networks” component is installed, then on the server and 
clients, make sure that the “IPX/SPX-compatible Protocol” or the 
“TCP/IP Protocol” is installed.

❏

The print server and clients should be set on the same network 
system, and they should be under the same network management 
beforehand.

❏

The screen may vary depending on your operating system version.

Setting up your printer as a shared printer

When the print server’s OS is Windows Me, 98, or 95, follow the 
steps below to set the print server.

1. Click 

Start

, point to 

Settings

, then click 

Control Panel

.

2. Double-click the 

Network

 icon.

3. Click 

File and Print Sharing

 on the Configuration menu.

4. Select the 

I want to be able to allow others to print to my 

printer(s).

 check box, then click 

OK

.

5. Click 

OK

 to apply the settings.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands