Epson Aculaser C1600 User Manual Download Page 72

Page: 72 / 93

Ready
indicator
(green)

Error
indicator
(orange)

Toner
indicator
(orange)

Display of
Remote
Panel
Program

Condition

Action

Off

Blinking

TOP COVER
OPEN /
CLOSE TOP
COVER

Front cover or top cover
is open.

Close the front cover
and top cover.

The photoconductor
unit is not installed.

Install the
photoconductor unit.

Off

Rapid
blinking

TRANSFER
JAM, FUSER
JAM,
OUTPUT
JAM / OPEN
TOP COVER

Media jam

Clear the jam, close the
covers, and then
continue with the print
job.

PROCESS
ERROR-BELT
, PROCESS
ERROR-IDC

Process error

Open and close the
printer’s covers.

If the error is not
corrected, turn off the
printer. After a few
seconds, turn on the
printer.

Off

All blinking

P/U LIFE
END

Photoconductor unit
end

Replace the
photoconductor unit.

* Differs depending on the toner status.

Service Message

This message indicates a more serious fault that can only be corrected by a customer service engineer.

Ready
indicator
(green)

Error
indicator
(orange)

Toner
indicator
(orange)

Display of
Remote
Panel
Program

Condition

Action

Rapid
blinking

All blinking

SERVICE
CALL(XXXX)

Fatal error

Turn off the printer. After
a few seconds, turn on
the printer.

If the problem persists,
contact your vendor or
authorized service
provider.

AcuLaser C1600 User’s Guide

Troubleshooting

Summary of Contents for Aculaser C1600






























































































Search results

Summary of Contents for Aculaser C1600

Reviews:

Related manuals for Aculaser C1600

Brands by name

Popular brands

Epson Aculaser C1600, User Manual

Search results

Summary of Contents for Aculaser C1600

Reviews:

Related manuals for Aculaser C1600

Brands by name

Popular brands