epiphan Pearl-2 Rackmount User Manual Download | Manualshive

Page: 233 / 497

background image

Pearl-2 User Guide

Configure encoding

Configure encoding

You can modify the encoding settings for each channel. The encoding settings let you fine tune your channel
recording or live stream. You can select a specific frame size, bit rate, audio or video codec, and more.

Topics include:

l

Codecs and file format compatibility

l

Configure video encoding

l

Configure audio encoding

l

Multi-encoding and channel as a source

To configure channel encoding using AV Studio, see

Configure channel encoding using AV Studio

.

Codecs and file format compatibility

Pearl-2 supports the following video and audio codecs.

Table 40

Supported video codes

Value

Description

H.264

H.264 is the default video codec configured for the channels on Pearl-2. This codec
provides high quality video while using low bandwidth and is the preferred codec to
use with the system.

Motion JPEG

Motion JPEG is suitable for live streaming and video; however, you can experience low
quality images while using high bandwidth. Motion JPEG does not support audio.

Table 41

Supported audio codecs and bitrate guidance

Value

Description

AAC

AAC is comparable to MP3 and may even provide better sound quality at a similar
sample bitrate. Supported sampling bitrate values are: 16, 22, 44 and 48K kHz.

Setting the channel bitrate to match the audio source's bitrate provides the best
sound quality and avoids audio resampling. Most digital signals (HDMI
or SDI sources) use 48 kHz. Most digital signals (HDMI or SDI sources) use 48 kHz
audio. For analog signals, 44 kHz provides a good quality audio sample.

The maximum bitrate for mono encoding of a 44 kHz signal is 264 kbps. For stereo,
320 kbps is supported. Note that lower bitrates (e.g. 32 kbps) with a 44 kHz signal

220

«
...
231
232
233
234
235
...
»

Summary of Contents for Pearl-2 Rackmount


















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Pearl-2 Rackmount

Brand: LaView Pages: 96

Brand: Audiovox Pages: 2

Brand: Grundig Pages: 48

Brand: IC Realtime Pages: 13

Brand: Watchguard Pages: 19

Brand: AUSTAR Pages: 36

Brand: Microview Pages: 17

Brand: Vacron Pages: 21

Brand: Mio Pages: 21

Brand: Atomos Pages: 2

Brand: Wisenet Pages: 14

Brand: Wisenet Pages: 13

Brand: Vicon Pages: 48

DS-80xxHM(F)I/xx Series

Brand: HIKVISION Pages: 10

Brand: HIKVISION Pages: 101

Brand: PACOM Pages: 102

Brand: PACOM Pages: 160

Brand: Pace Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands